Kenmore Refrigerator 363.58252894 (36358252894, 363 58252894) Parts

Genuine Ge part

Water Line Sleeve

By: Ge

Part Number: WR2X8933

Do-It-Yourself Stories from Customers like You Clogged drain tube Keith P. • Ivoryton , CT • March 03, 2017

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

Genuine Ge part

Blade Condenser Fan Assembly

5.0 (3)

By: Ge

Part Number: WR60X10030

Do-It-Yourself Stories from Customers like You Condenser fan blade broke when we were cleaning under the refrigerator Carla S. • Raytown , MO • July 31, 2015

It was fairly simple. The blade just slides onto the post of the condenser. Thanks to Appliance Pros, we should not have this problem again. We were offered to buy a special 28" long brush made to clean the refrigerator coils, and it works great! :) Read more

Genuine Ge part

Ring Compression

4.5 (2)

By: Ge

Part Number: WR02X10323

Do-It-Yourself Stories from Customers like You Refrigerator and freezer not cooling. Eric O. • Long Beach , CA • August 07, 2017

This is in a 15 year old Built-in Monogram that had the compressor replaced a few years ago. Before discovering the motor failure I replaced the main board since a Refrigeration Contractor I know said that if it wasn't bad it would be soon since those parts typically only last around eight years. The motor replacement is pretty simple; more time is spent getting to the motor and re-assembling everything than actually changing the motor. The trickiest part is getting the fan set correctly on... Read more

Genuine Ge part

Stop Door Wh

4.0 (4)

By: Ge

Part Number: WR2X9300

Do-It-Yourself Stories from Customers like You Broken refrigerator door stop James W. • Alexandria , VA • August 21, 2017

Replaced the broken part. Exact fit. 15 minutes. Works perfectly. Read more

Genuine Ge part

Bracket Evaporator Fan Sm.

5.0 (2)

By: Ge

Part Number: WR02X10100

Do-It-Yourself Stories from Customers like You Ice maker was getting clogged with ice and would not dispense. Randall D. • Aylett , VA • December 08, 2019

Found that piece of auger was broken up front. Ordered auger and several other parts associated with ice maker just to be sure. Also replaced condenser motor which was making noise. Read more

Genuine Ge part

Cradle Actuator

By: Ge

Part Number: WR17X3493

Genuine Ge part

Fill Cup

By: Ge

Part Number: WR29X10063

Genuine Ge part

Shelf Support (Single)

By: Ge

Part Number: WR2X4676

This shelf support secures an interior refrigerator shelf in place so food items stay level and storage remains organized. It replaces a cracked or worn support to restore proper shelf seating and stability. What it does

Holds a refrigerator shelf or shelf trim in the correct position to prevent sagging or tipping
Restores stable support for glass or wire shelving that no longer stays seated
Helps eliminate shelf movement that can cause items to slide or spill
Works where a broken, chipped, or missing support prevents proper shelf alignment

What's included One shelf support Install notes

Disconnect power to the appliance before starting any repair and empty the shelf area
Remove the affected shelf or trim to access the support; reinstall shelf to confirm correct seating
Use basic hand tools as needed and avoid forcing parts to prevent further damage
Replace all affected pieces for consistent shelf alignment

Genuine Ge part

Ice Auger Blade

5.0 (2)

By: Ge

Part Number: WR2X7783

This replacement part is an ice auger blade, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice auger blades are usually found in ice maker assemblies and are used during the ice-making and dispensing process. These blades are what are used when the user is in need of shaved or crushed ice. The mechanism takes full ice cubes and cuts the ice cubes down to create the different types of ice. A new ice auger blade might be needed if the user noticed that the current blades are dull or unable to cut ice. It is possible that the blades become dull over time after many years of use, so replacing them might be a good idea. Be sure the power is completely off before attempting to repair this part.This ice auger blade is sourced directly from the manufacturer and is a genuine OEM replacement part. Note that this part is sold individually.

Do-It-Yourself Stories from Customers like You Ice crusher repair GE Monogram counter depth. Glenn J. • El Cajon , CA • July 27, 2020

This was a very easy repair, the on-line video at AppliancePartsPros.com was helpful. The Helix was spinning freely (meaning, the Auger Blade was not holding it in place on the Auger). Pulling the assembly apart was a snap, and very logical (the video is perfect if you get lost). The family is now enjoying both crushed and cubed ice - and the redesign of the Auger Blade seems to prevent clogging in the ice shoot. Read more