Kenmore Refrigerator 363.9557752 (3639557752, 363 9557752) Parts
Genuine Ge part
By: Ge
Part Number: WR72X211
Left side.
Do-It-Yourself Stories from Customers like You
Shelf in refrigerator needed to be replaced Daniel S. • Jacksonville , NC • September 29, 2018
Ordered parts from appliance parts pros and completed installation myself
Read more
More
Genuine Ge part
By: Ge
Part Number: WR17X3670
Genuine Ge part
By: Ge
Part Number: WR17X3909
Lower fresh food section.
Do-It-Yourself Stories from Customers like You
Plastic shield light was warped from heat of light bulbs and would no longer stay in place on rear wall of refrigerator Paul S. • Green Valley , AZ • February 28, 2015
I needed to find a parts supplier who could provide a replacement part at a reasonable price. I first tried the manufacturer, General Electric, but they only showed freezer replacement parts for the model of my side-by-side refrigerator. In looking over a list of parts available for this model there seemed to be a possible part that sounded like a match but there was no picture to confirm that this was the correct replacement part. When i clicked the Appliance Parts Pros web site They had a...
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X9300
Do-It-Yourself Stories from Customers like You
Broken refrigerator door stop James W. • Alexandria , VA • August 21, 2017
Replaced the broken part. Exact fit. 15 minutes. Works perfectly.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR17X3493
Genuine Ge part
By: Ge
Part Number: WR29X10063
Genuine Ge part
By: Ge
Part Number: WR2X7783
This replacement part is an ice auger blade, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice auger blades are usually found in ice maker assemblies and are used during the ice-making and dispensing process. These blades are what are used when the user is in need of shaved or crushed ice. The mechanism takes full ice cubes and cuts the ice cubes down to create the different types of ice. A new ice auger blade might be needed if the user noticed that the current blades are dull or unable to cut ice. It is possible that the blades become dull over time after many years of use, so replacing them might be a good idea. Be sure the power is completely off before attempting to repair this part.This ice auger blade is sourced directly from the manufacturer and is a genuine OEM replacement part. Note that this part is sold individually.
Do-It-Yourself Stories from Customers like You
Ice crusher repair GE Monogram counter depth. Glenn J. • El Cajon , CA • July 27, 2020
This was a very easy repair, the on-line video at AppliancePartsPros.com was helpful.
The Helix was spinning freely (meaning, the Auger Blade was not holding it in place on the Auger).
Pulling the assembly apart was a snap, and very logical (the video is perfect if you get lost).
The family is now enjoying both crushed and cubed ice - and the redesign of the Auger Blade seems to prevent clogging in the ice shoot.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X8676
Genuine Ge part
By: Ge
Part Number: WR2X8989
Genuine Ge part
By: Ge
Part Number: WR01X10064
Genuine Ge part
By: Ge
Part Number: WR01X10204
Genuine Ge part
By: Ge
Part Number: WR02X10395
Do-It-Yourself Stories from Customers like You
Water valve and defrost drain tube were bad. Richard W. • Jacksonville , FL • June 24, 2017
Replaced them both.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR07X10098
Genuine Ge part
By: Ge
Part Number: WR12X952
Genuine Ge part
By: Ge
Part Number: WR14X456
Genuine Ge part
By: Ge
Part Number: WR17X10190
Do-It-Yourself Stories from Customers like You
Yellowing of handles and the recess portion of the water/ice dispenser recess Michael S. • Panama City Beach , FL • March 10, 2018
The handles were a simple fix. Just pop out the door trim, which I did by pulling on the very top and bottom of the trim to get it started. Then removed two star screws from the handle. I had to work the chrome plastic top and bottom handle caps off, then reversed the process for installing the new handle.
The Recess/Dispenser was a bit more tricky. I pried the trim and control panel off with a putty knife, then the rest was fairly obvious, such as removing screws and wiring connectors. ...
Read more
More