Kenmore Refrigerator 363.9644211 (3639644211, 363 9644211) Parts

This Door Spacer positions the refrigerator door components with the correct clearance so the door swings smoothly and sits level. Replacing a worn spacer can restore alignment, reduce rubbing or squeaks, and help maintain proper gasket contact.

• Maintains proper spacing and alignment of the door assembly
• Helps the door open and close smoothly, reducing friction and wear
• Can address issues like door rubbing, squeaking, or not sitting level
• Supports consistent gasket contact for a reliable seal

• Unplug the refrigerator before servicing
• Support the door and remove the necessary hardware to access the spacer location
• Note spacer orientation; install the new spacer and reassemble
• Adjust hinges if needed

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

The duct foam assembly insulates and seals the refrigerator's air duct to keep cold air moving efficiently between compartments. Replacing worn or missing foam helps restore airflow control, reduce moisture at the vent, and stabilize temperatures.

• Seals the air duct to prevent warm-air leaks and maintain proper airflow
• Insulates the duct to help keep fresh-food temperatures consistent
• Helps reduce condensation or frost forming around the vent area
• Typical indications include temperature swings, a warm fresh-food section, moisture/frost near the duct, or visibly damaged/missing foam

• Disconnect power to the refrigerator before servicing
• Remove interior shelves/panels as needed to access the air duct; note foam orientation before removal
• Clean the mounting surface; seat new foam fully and evenly to create a complete seal—do not obstruct a damper door or sensor if present
• Restore power and verify airflow and sealing around the vent

Please note: You may also need to order an adapter. For the adapter to convert the male connector from rectangular to oval use part number WR29X10049. Water valve in kit is part# WR57X10033.

This leveling leg supports and stabilizes the refrigerator cabinet. Adjusting it keeps the unit level so doors align and seal correctly, helping reduce vibration and noise for smoother, more reliable performance.

• Threads into the base to support and level the appliance
• Allows height adjustment for proper door alignment and gasket contact
• Helps reduce rocking, vibration, and rattling noises
• Resolve issues like doors not closing fully, uneven gaps, or a wobbly cabinet

• Disconnect power and move the appliance carefully to access the leg
• Use a helper and protect flooring; tip the unit slightly and support it securely
• Unthread the old leg; hand-thread the new leg, then adjust as needed with a wrench
• Level front-to-back and side-to-side; avoid cross-threading or overtightening

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This defrost thermostat monitors evaporator temperature and controls power to the defrost heater, shutting it off at the correct point in the cycle. Replacing a failed thermostat helps clear frost and restore stable cooling and airflow.

• Senses evaporator coil temperature in the freezer
• Closes when cold to allow the defrost heater to run; opens as the coil warms to terminate defrost
• Helps prevent excessive frost buildup and maintains proper airflow
• Typical failure signs: heavy frost on the evaporator/back wall, weak airflow, warm fresh-food section, unit runs constantly or never defrosts

• Disconnect power and wear appropriate safety gloves before servicing
• Access the evaporator behind the rear freezer panel; note wire routing and original mounting on the refrigerant tubing
• Install the new thermostat in the same location with firm thermal contact; do not damage coil fins or tubing
• If your model uses spliced leads, use approved connectors and secure all joints; replace all covers before restoring power

This vinyl sleeve fits over a rod, tube, or wire in the refrigerator to protect and cushion contact points. It reduces wear and vibration and helps keep components aligned for smooth, reliable operation.

• Provides a protective barrier at contact points to prevent abrasion or marring
• Helps maintain spacing and alignment for a snug, proper fit
• Cushions to damp vibration and reduce rattles or squeaks
• Replace if the sleeve is missing, cracked, hardened, or if components feel loose or make noise

• Disconnect power; turn off the water supply if working near water lines
• Note the sleeve's original location and orientation; take a photo for reference
• Remove the old sleeve and any debris; slide the new sleeve into the same position
• Check clearance and resecure related parts before restoring power

Size: 10-16 ab.

Includes 12 screws. Size: 8-18 ab.

This rear mobility wheel replaces a worn or broken wheel on the back of your refrigerator, restoring smooth rolling movement so you can pull the unit out safely for cleaning, servicing, or leveling without dragging or floor damage.

• Mounts to the rear base/roller bracket to support and roll the refrigerator for positioning or service
• Replace if the wheel is cracked, missing, flat-spotted, or seized
• Common symptoms: unit is hard to move, scrapes the floor, sits unevenly, or makes grinding noises when moved
• Helps maintain proper cabinet support during movement

• Disconnect power and turn off the water supply before servicing
• Protect flooring and use a helper—appliances are heavy and can tip
• Access the rear base area; remove the old wheel and install the new wheel using the existing hardware
• After re-positioning, re-level the refrigerator per the owner's manual

This OEM-style support secures internal components to restore proper alignment and stability. Use it to replace a cracked or worn support so shelves, drawers, and mounted parts stay in place and stop shifting or rattling. What it does:

• Stabilizes and supports internal appliance components to maintain proper alignment.
• Replaces cracked, broken, or worn supports that cause sagging, shifting, or rattling.
• Restores mounting points so shelves, drawers or panels sit and operate correctly.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Basic hand tools are typically required; you may need to remove adjacent trim or shelves for access.
• Inspect surrounding mounting points and clips; replace any additional damaged hardware.

Replacement screw that secures panels, trim and internal brackets to keep appliance components stable and rattle-free. Use when originals are missing, stripped, or broken to restore proper fit and safe operation. What it does:

• Secures panels, control housings, trim and small brackets so parts stay aligned and stable.
• Replaces missing or damaged fasteners that cause rattling, vibration, or loose assemblies.
• Keeps electrical and mechanical components properly positioned for reliable operation.
• Intended as a direct replacement where the OEM screw specified for the application is required.

• Disconnect power and unplug the appliance before starting any repair.
• Use the correct screwdriver or bit and seat the screw squarely to avoid stripping the head or threads.
• Do not overtighten—stop when snug to prevent damage to panels or plastic components.
• Keep removed screws organized; replace only with the identical OEM screw for proper fit.