Kenmore Washer 417.40412700 (41740412700, 417 40412700) Parts

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

The Door Strike is an OEM replacement part for Frigidaire washing machines. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation.

Symptoms of a faulty door strike may include:

• The washer door not closing or latching properly
• Leaks or water seeping out from the door area
• Excessive noise or vibration due to an improperly sealed door

Causes of needing to replace the door strike can include normal wear and tear over time, physical damage or bending of the strike, or issues with the door latch mechanism not aligning correctly.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore washing machine models.

This top-front bracket secures the appliance's top or front panel in place to keep panels aligned and stable. Replacing a damaged bracket restores proper panel fit and reduces rattling or loose trim. What it does:

• Mounts and supports the top/front panel to the appliance frame
• Prevents panel movement that can cause noise or misalignment
• Helps maintain correct door or control-panel fit where applicable
• Used when bracket is bent, cracked, or missing mounting holes

• One top-front bracket

• Disconnect power (and water, if applicable) before starting any repair
• Remove necessary trim or panels to access the bracket; retain original fasteners unless new hardware is supplied
• Align bracket and reinstall screws securely; avoid overtightening to prevent strip-out
• If other mounting hardware is damaged, replace it to ensure a secure fit

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support