Kenmore Dryer 417.84082500 (41784082500, 417 84082500) Parts

The Motor is an OEM part for Frigidaire dryers. It is responsible for driving the drum rotation in the dryer, allowing for the tumbling and drying of clothes. It converts electrical energy into mechanical motion, providing the necessary power to spin the drum and circulate air for efficient drying.

Causes of a faulty dryer motor can include wear and tear over time, electrical malfunctions, or physical damage. These factors can result in issues such as the drum not spinning, unusual noises during operation, or the dryer not heating properly.

Symptoms of a bad dryer motor may include:

• The drum not rotating or spinning
• Unusual grinding or squealing noises while the dryer is in use
• Dryer not generating heat or insufficient drying performance

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Secures the fan housing to its mounting points. Replace if the clip is broken, missing, or worn to eliminate rattles and prevent air leaks in your dryer.

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

This is a flexible seal that fits around the inner door glass of the dryer, creating an airtight barrier between the door panel and the drum area. It prevents heated air from escaping and keeps lint contained within the drum during drying cycles. Replace this gasket if you notice heat leaking from around the door, longer drying times, or if the seal is cracked, torn, or coming loose.

Stacking kit bracket module that secures your dryer on top of a washer. Replaces cracked, broken, or missing brackets to restore safe stacking.

This is a small translucent light pipe that channels light from the circuit board to the front control panel, allowing indicator lights to be visible during dryer operation. It fits into the control panel housing and directs LED or bulb light to the display area. Replace this part if your dryer's indicator lights appear dim, unlit, or inconsistent even though the control board is functioning properly.

Fix error codes or unresponsive controls with a new dryer electronic control board. Restores cycle selection and timing. DIY install in under 1 hour.

This replacement plug seals an unused opening on compatible appliances to help prevent moisture, dirt and pests from entering and to restore the original appearance and fit. It's a simple, low-cost part for routine repairs. What it does

• Seals an access hole or unused opening to help keep moisture and debris out
• Helps block pests and contaminants from entering the appliance cabinet
• Secures wiring or tubing routing where a protective cap is required
• Restores original fit and finish at the plug location

• One replacement plug

• Disconnect power to the appliance before beginning any work
• Remove the access panel or trim necessary to reach the plug location
• Press the plug into place; small hand tools may help for snug seating
• Inspect surrounding gaskets and panels for damage while installing

Secures internal dryer components and assemblies. Replacement needed when bracket is cracked, broken, or missing to restore proper fit and alignment.

Replacement use and care guide manual for your dryer. Needed when original manual is lost, damaged, or missing. Provides operating instructions.

Technical data sheet for your dryer. Provides specifications, wiring diagrams, and installation details. Replace if lost, damaged, or illegible.

This mounting bracket secures internal components in place to keep appliance parts aligned and stable during normal use. Replacing a damaged bracket restores proper fit and support for affected assemblies. What it does:

• Provides structural support for internal panels or assemblies to prevent shifting and noise
• Helps maintain proper alignment of moving parts to reduce wear
• Stops rattling or vibration caused by a broken or bent bracket
• Keeps connected components securely attached after repair or reassembly

• One mounting bracket

• Disconnect power and water before starting any repair
• Inspect surrounding fasteners and hardware; replace any stripped screws for a secure fit
• Use proper-size tools to avoid damage to mounting holes or nearby components