Kenmore Dryer 417.92142101 (41792142101, 417 92142101) Parts

This control thermostat regulates the dryer's operating temperature. It senses exhaust air heat and cycles the heater on and off to maintain consistent drying performance and help protect the appliance from overheating. What it does:

• Monitors exhaust temperature and controls the heating element to hold the selected heat level
• Helps prevent overheating by cycling heat off when the target temperature is reached
• Supports even drying and consistent cycle times
• Typical failure symptoms: no heat or not enough heat, long dry times, runs too hot, inconsistent temperatures

• 1 control thermostat

• Disconnect power before servicing; if gas, also shut off the gas supply
• Access location varies by model; typically mounted on the heater housing or exhaust duct
• Transfer wire leads one at a time to the new thermostat and secure with the original screws
• After reassembly, clean the lint path and ensure good airflow to prevent repeat failures

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

This hinge secures the door to the cabinet and provides a smooth pivot. Replacing a bent or worn hinge restores proper alignment and reliable latching so the door opens easily and closes securely.

• Provides the pivot point for the door to open and close
• Supports door weight and keeps it aligned with the latch/strike
• Wear or damage can cause sagging, rubbing, or squeaking
• A misaligned door may not engage the door switch, preventing the cycle from starting

• Disconnect power before servicing; shut off gas supply
• Support the door before removing mounting screws to avoid strain or damage
• Note hinge orientation; transfer any spacers/shims and reuse existing hardware
• Align the hinge, snug screws, then tighten fully and test door operation

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This safety thermostat is a temperature-limiting switch that helps protect your refrigerator/freezer by opening the circuit if temperatures reach an unsafe level, preventing damage to components and reducing fire risk. What it does:

• Monitors internal temperature and interrupts power when the preset limit is exceeded
• Prevents overheating of heating elements or compressors in defrost and refrigeration circuits
• Helps stop continuous run or cycling caused by thermal faults
• May be used as part of the fridge/freezer safety/limit control system

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle carefully and avoid kinking or crushing any sensing element or capillary tube
• Verify function and wiring location against your model's service manual or wiring diagram

This replacement screw secures appliance panels and components to restore proper fit and reduce movement. It's a simple, direct fix when small fasteners are missing, worn, or stripped and panels sit loose or rattle. What it does:

• Secures trim, panels, or internal components to keep parts aligned
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or damaged screws that prevent proper panel attachment
• Restores a safe, snug fit for covers and access panels

• Disconnect power or fuel supply before accessing the appliance for safety.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Tighten until snug; avoid over-tightening to prevent damage to threads or housing.
• Keep small parts away from children and pets during installation.

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces

Hex washer head ,10-32 x 0.375. Ground

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip