Kenmore Refrigerator 596.68252802 (59668252802, 596 68252802) Parts

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

Touch up paint Read more

Replaced It With New One Read more

Very easy.Just set right in Read more

My son broke the bottom shelf on the refrigerator door. I found the model number inside the frig and within 5 mins the part was on it's way! Ordered it Saturday morning , and arrived on Monday! Too easy! Slipped right into place! Read more

Replaced the gasket . Parts were were here one day after ordered . U-tube video was a big help. Went faster and easier than expected . Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

• Door sweating

Removed old gasket. Replaced old gasket with new. A small wooden block helped seat gasket. Read more

I called Sears to schedule a service call for Sat. Morning. At 11:00 a.m. A service man called and said he was going to do the service call (the original tech was going to be delayed), so he had been scheduled instead. He had another call before he could get to me (an hour drive one way And he would get lunch and see me later. I asked him about how long it might take, he said they do not charge by the hour. He said he couldn't remember for sure, but it was between $200.00 and $250.00, but... Read more

Purchased 2 replacement feet risers. A very awkward repait. Read more

New mounting screws and handle. BTW, the parts have been redesigned to be more robust. Easy fix and the Refrigerator// Freezer look like new. Read more

First, I had to replace a cracked roller so I could roll the frig out. I did this by tilting it slightly and shoving a shim underneath. I had to use two shims to get enough clearance for the wheel. I unscrewed the old wheel, screwed in the new one pretty easy, removed the shims and rolled it out. Then I unplugged the frig from the power socket, removed 6 screws from the back panel, and pulled out the old drain kit, which had become clogged with dirt and dust. I put in the new drain kit,... Read more

There is nothing you can't do given the right YouTube video! We disassembled the bottom mount freezer n our Jenn Air refrigerator to remove all the ice and then located the clogged grommet on the back of the unit and cleared it and added a notch. In the process of reassembling we broke the bracket on a part that should have been the easiest portion of the entire installation! In seconds we located and ordered the part on your site. It arrived in a couple of days and then we removed the door and... Read more

The noise seemed to be caused by a vibration. The condenser fan motor seemed to have a vibration. I didn't need the fan blade as it came off in good condition. Read more