Kenmore Refrigerator 596.77532603 (59677532603, 596 77532603) Parts

Seals the damper opening to prevent air leakage between compartments. Replace when worn to restore consistent airflow and stable temperatures.

This replacement motor restores powered rotation to the assembly it drives, bringing smooth, dependable operation back to your appliance. Replacing a weak, noisy, or seized motor can resolve no-run or intermittent performance of the connected function. What it does

• Converts electrical power into controlled shaft rotation to operate the connected mechanism
• Failure signs can include humming or grinding noises, overheating odor, or the feature not starting
• Excess vibration or heat can indicate worn bearings or windings

• 1 motor

• Disconnect power (and shut off water if applicable) before servicing
• Note wire connections and orientation; transfer any brackets, grommets, or attached parts from the original motor if required by your model
• Ensure the shaft spins freely and clearances are correct before reassembly
• Restore power and test; monitor for abnormal noise or heat on first run

Ice maker won't stop making ice or won't start? This shutoff arm controls ice production by sensing bin level. Simple DIY fix in under 30 minutes.

Freezer air grill cover that mounts over the evaporator panel in the freezer compartment. Replace if cracked, broken, or tabs are damaged or missing.

Left-side slide bracket that secures and guides drawer assemblies in refrigerators. Replaces worn, cracked, or broken brackets to restore alignment.

Fix intermittent or unresponsive controls with this single-pole, single-throw rocker switch. Restores reliable on/off operation for refrigerators.

Upper freezer glide that supports and guides the freezer drawer for smooth opening and closing. Replaces a worn or damaged glide to help eliminate binding, scraping, and uneven drawer movement. What it does:

• Guides and supports the upper freezer drawer for smooth travel; a failed glide often causes the drawer to stick or catch.
• Reduces metal-on-metal contact and scraping noises when opening or closing the drawer.
• Helps restore proper drawer alignment to prevent uneven gaps or rubbing against the cabinet.
• Lowers stress on adjacent components by returning consistent, even drawer movement.

• Disconnect power to the appliance before beginning any service work.
• Remove freezer contents and the drawer assembly per the manufacturer's instructions to access the glide.
• Replace the glide following the OEM diagram/steps; keep fasteners and mounting points aligned during reassembly.
• Test drawer operation after installation and adjust as needed for smooth, even travel.

Right-hand adapter bracket secures and aligns refrigerator panels and components. Replaces worn, damaged, or broken brackets to restore proper fit.

Left-hand adapter bracket secures and aligns refrigerator components. Replace if your original bracket is cracked, broken, or missing for proper fit.

Right-hand slide bracket secures drawer or shelf slide assemblies in refrigerators. Replace if cracked, broken, or causing misalignment issues.

Hex head sheet metal screw secures panels, brackets, and internal components in refrigerators and freezers. Replace missing, corroded, or stripped screws.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.

This hinge shim adjusts the alignment and spacing of your refrigerator door for proper closure. It ensures the door seals correctly and maintains proper clearance during operation. Replace it if your refrigerator door doesn't close properly, has uneven gaps, or if the door sags and doesn't align with the cabinet.

Fix loose wiring or rattling sounds in your refrigerator with this terminal block clip kit. Secures harnesses and panels to restore proper fit.

Upper door hinge secures and pivots your refrigerator door for smooth operation. Replace if cracked, damaged, or causing door misalignment and gaps.