Kenmore Refrigerator 596.77602804 (59677602804, 596 77602804) Parts

This user interface control board sits behind the dishwasher's control panel, reading button presses and lighting indicators while communicating with the main control. Replacing a failed UI board can restore responsive controls and proper cycle selection. What it does:

• Interprets keypad/touchpad inputs and sends selections to the main control
• Powers and manages console indicator lights
• Common failure symptoms include an unresponsive or intermittent control panel, no indicator lights, or a unit that won't start or accept selections

• Disconnect power at the breaker before service and use ESD precautions; handle the board by its edges
• Access the UI by removing the console/inner door as directed in the tech sheet
• Transfer and fully seat the ribbon cable and wire harnesses; reuse mounting hardware as required
• After reassembly, restore power and run keypad/diagnostic checks per the unit's tech sheet, if applicable

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Directs water into the ice maker fill cup. Replace this funnel if cracked, broken, or missing to ensure proper water flow and prevent spills during ice production.

Replacement mounting screw for refrigerators. Secures panels, trim pieces, and small assemblies. Needed when original screw is missing or damaged.

This cover hinge assembly secures and guides the appliance lid or top panel so it opens and closes smoothly. Replacing a worn hinge restores proper lid alignment and helps eliminate sticking, sagging, or uneven closure. What it does:

• Provides a pivot point for the lid/top cover, holding it in the correct position during use
• Restores smooth opening and closing when original hinge is bent, worn, or broken
• Helps eliminate lid sag, misalignment, or rubbing against the cabinet
• Works with the appliance's existing bracketry and fasteners to maintain fit and function

• One cover hinge assembly

• Basic hand tools required; keep fasteners organized for reassembly
• Disconnect power and follow appliance-specific safety guidelines before beginning repair
• Inspect mating surfaces and replace any damaged screws or brackets for a secure fit

This replacement lower basket tray restores the support and stability for dishes in the dishwasher's lower rack, helping keep items in place and maintain proper wash coverage. What it does

• Provides a stable surface for plates, bowls and cookware in the lower rack
• Keeps items from shifting or nesting during the wash cycle
• Helps maintain proper water flow and spray coverage by supporting load positioning
• Replaces cracked, warped or missing trays that cause rattling or unstable loads

• One lower basket tray

• Typically snaps into place on the lower rack; inspect existing mounting points for alignment
• No special tools usually required, but keep small parts to prevent loss during install
• Turn off power to the dishwasher and follow the manufacturer's safety guidance if you must move the appliance

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

Refrigerator bottle trivet shelf holds bottles securely in the fridge section. Replace if cracked, broken, or missing to restore proper storage.

Secures refrigerator water tube to cabinet, preventing shifting and rubbing. Replace if cracked or loose. Verify fit with your model number.

Plastic cover that conceals the top door hinge on your refrigerator. Replaces cracked, broken, or missing hinge covers for a clean finished look.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Foam insulation panel that fits inside refrigerator doors to maintain temperature efficiency. Replace if cracked, compressed, or missing.

This drive coupling connects the washer motor to the transmission, transferring power to spin and agitate the tub. Replacing a worn coupling restores proper drivetrain engagement and reduces slipping, grinding, or loss of agitation. What it does:

• Transfers rotational force from the motor to the transmission so the washer can agitate and spin.
• Failsafe for worn motor-to-gearcase connection; a broken coupling commonly causes no-agitate or no-spin symptoms.
• Can produce burning smell, loud grinding, or slipping when deteriorated.
• Helps prevent further damage to the motor or transmission by isolating shock loads.

• Disconnect power and water before starting any repair.
• Basic disassembly of the washer cabinet and access to the motor/transmission area is required.
• Verify correct alignment of tabs/slots during installation to ensure proper engagement.

Ice maker shifting or loose? This mounting bracket secures your ice maker assembly in place to restore stable positioning and reliable ice production.

Replace your cracked, broken, or missing refrigerator door handle. This exterior handle mounts to the door for opening and closing your appliance.