Kenmore Refrigerator 596.77603803 (59677603803, 596 77603803) Parts

Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

This wire harness connects and organizes your appliance's internal wiring. It delivers power and control signals between the control system and components, restoring reliable connections when the original harness is damaged or heat-stressed. What it does:

• Distributes power and control signals between boards, sensors, motors, valves, and other components
• Replaces cut, brittle, corroded, or melted wiring and terminals
• Can help resolve intermittent operation, components not running, or visible burn/arc marks at connectors
• Maintains proper wire routing and strain relief to reduce future fatigue or shorts

• 1 wire harness assembly

• Disconnect power; shut off water or gas supplies before service
• Label or photograph each connector to ensure one-for-one transfer
• Route the harness along the original path; secure with existing clips/ties and keep clear of hot, sharp, or moving parts
• Push connectors straight and fully until they lock; avoid pulling on wires during removal/installation

Replaces a broken or worn top left door hinge on your refrigerator. Secures the door to the cabinet for proper alignment and smooth pivoting movement.

Rubber grommet that cushions wiring or hoses at sheet metal openings in refrigerators and freezers. Replace if worn, cracked, or missing.

Size: 8 x 1-1/4 inch.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Screw: 8-16 x 3/8 inch.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Ice maker not filling or leaking? This water tube routes water from the inlet to the ice maker fill valve. Replaces cracked or clogged tubing in your fridge.

Dispenser facade cracked or discolored? This trim assembly restores your refrigerator's dispenser appearance and proper fit. Straightforward install.

Left-side slide bracket that secures and guides drawer assemblies in refrigerators. Replaces worn, cracked, or broken brackets to restore alignment.

Protective housing that covers refrigerator fan components. Replace if cracked or broken to ensure proper airflow and protection. Confirm fit with model.

This is a plastic guide that secures and routes the water supply line inside the refrigerator. It keeps the tubing properly positioned so it doesn't kink or interfere with moving parts like drawers or shelves. Replace this guide if it is broken or missing, which can cause the water line to become pinched, kinked, or disconnected.

This insulation wraps around the water tank inside the refrigerator to help maintain consistent water temperature and prevent condensation. It serves as a thermal barrier that keeps chilled water at the proper temperature. Replace if the insulation is damaged, missing, or if you notice excessive condensation or inconsistent water temperature from the dispenser.

Hex head sheet metal screw secures panels, brackets, and internal components in refrigerators and freezers. Replace missing, corroded, or stripped screws.