Kenmore Refrigerator 596.78533800 (59678533800, 596 78533800) Parts

Replacement mounting screw for securing appliance panels, brackets, or trim. Restores tight fit when original fastener is missing, stripped, or rusted.

This replacement motor restores powered rotation to the assembly it drives, bringing smooth, dependable operation back to your appliance. Replacing a weak, noisy, or seized motor can resolve no-run or intermittent performance of the connected function. What it does

• Converts electrical power into controlled shaft rotation to operate the connected mechanism
• Failure signs can include humming or grinding noises, overheating odor, or the feature not starting
• Excess vibration or heat can indicate worn bearings or windings

• 1 motor

• Disconnect power (and shut off water if applicable) before servicing
• Note wire connections and orientation; transfer any brackets, grommets, or attached parts from the original motor if required by your model
• Ensure the shaft spins freely and clearances are correct before reassembly
• Restore power and test; monitor for abnormal noise or heat on first run

Replacement door handle for your refrigerator. Restores secure grip when original is cracked, broken, or worn. Mounts directly to door for safe opening.

Refrigerator not cooling or humming without starting? The compressor pumps refrigerant to cool your fridge. Requires EPA certification for install.

Replace your refrigerator's door hinge bushing to restore smooth door movement and eliminate noise. Guides and cushions the hinge to reduce friction and wear.

Seals the damper opening to prevent air leakage between compartments. Replace when worn to restore consistent airflow and stable temperatures.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Freezer air grill cover that mounts over the evaporator panel in the freezer compartment. Replace if cracked, broken, or tabs are damaged or missing.

Supports and guides the upper freezer shelf for smooth sliding. Replace if shelf binds, sags, or tips when loaded. Confirm fit with your model number.

Condensate drain pan collects water under your refrigerator. Replace if cracked, leaking, or damaged to prevent floor water pooling and spillage.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Secures the pantry assembly in 36-inch refrigerator units, restoring proper alignment and stability. Replaces bent or broken braces for correct fit.

Left-side slide bracket that secures and guides drawer assemblies in refrigerators. Replaces worn, cracked, or broken brackets to restore alignment.

This temperature control bar is the actuator used to adjust and regulate the appliance's internal temperature, restoring proper temperature response for the bar/beverage control system. It provides a direct replacement for the OEM control bar assembly. What it does:

• Transfers user temperature adjustments to the control mechanism so the appliance reaches the set temperature
• Restores correct temperature changes when the control knob or selector fails to respond
• Helps address symptoms like incorrect temperature readings, temperature not changing, or unstable cooling behavior
• Works with the existing control housing and selector components to re-establish normal operation

• One temperature control bar

• Disconnect power before servicing to avoid electric shock
• Handle the part and surrounding components carefully to avoid damaging clips or wiring
• You may need to remove interior panels or the control housing to access the part;
• Verify the part number on your existing component before installation

Upper freezer glide that supports and guides the freezer drawer for smooth opening and closing. Replaces a worn or damaged glide to help eliminate binding, scraping, and uneven drawer movement. What it does:

• Guides and supports the upper freezer drawer for smooth travel; a failed glide often causes the drawer to stick or catch.
• Reduces metal-on-metal contact and scraping noises when opening or closing the drawer.
• Helps restore proper drawer alignment to prevent uneven gaps or rubbing against the cabinet.
• Lowers stress on adjacent components by returning consistent, even drawer movement.

• Disconnect power to the appliance before beginning any service work.
• Remove freezer contents and the drawer assembly per the manufacturer's instructions to access the glide.
• Replace the glide following the OEM diagram/steps; keep fasteners and mounting points aligned during reassembly.
• Test drawer operation after installation and adjust as needed for smooth, even travel.

Hex head sheet metal screw secures panels, brackets, and internal components in refrigerators and freezers. Replace missing, corroded, or stripped screws.