Kenmore Refrigerator 596.79542011 (59679542011, 596 79542011) Parts

Plug insert for refrigerators. Installs in cabinet or frame holes. Replace if cracked, broken, missing, or worn to restore clean appearance.

Secures hoses to fittings on water and vent lines to prevent leaks. Replace if loose, cracked, or connection drips. Confirm fit with your model number.

This refrigerator door flipper mullion is the folding center rail that bridges the gap between the doors. It helps complete the door seal and reduces condensation along the center for better temperature retention.

• Bridges the gap between doors to complete the center seal and improve efficiency
• Folds out of the way when a door opens; flips into place as the doors close
• Helps limit moisture/sweating at the middle of the refrigerator
• Replaces a cracked, loose, or broken mullion that causes air leaks, doors popping open, or poor sealing

• Disconnect power before servicing; remove door bins for access
• Remove mounting screws; lift off the assembly and disconnect the harness if equipped
• Transfer any end caps/brackets; ensure spring orientation and proper wire routing during reassembly
• After installation, verify smooth flipping action and a continuous gasket seal down the center

Freezer not cooling or ice maker stopped working? This evaporator fan motor restores cold air circulation when the original hums, won't spin, or fails.

Replacement door handle for your refrigerator. Restores secure grip when original is cracked, broken, or worn. Mounts directly to door for safe opening.

Replace your refrigerator's door hinge bushing to restore smooth door movement and eliminate noise. Guides and cushions the hinge to reduce friction and wear.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Replaces a cracked, warped, or missing cover on your refrigerator. Protects internal components and restores proper fit so parts stay secured.

Supports and guides the upper freezer shelf for smooth sliding. Replace if shelf binds, sags, or tips when loaded. Confirm fit with your model number.

This support bracket holds your refrigerator's pantry drawer in the proper position for smooth operation. It prevents the drawer from sagging and ensures proper alignment with door seals. Replace if your pantry drawer won't slide smoothly or appears to hang unevenly.

This circular component guides and directs water or ice from the dispenser to the user's container. Located in the refrigerator door dispenser area, replacement is needed when dispensing becomes inaccurate, messy, or completely blocked.

This slide temperature control is the user-access interface that moves the thermostat connection to select dryer heat levels. It restores responsive, indexed temperature selection for standard slide-style dryer controls. What it does

• Moves the internal contact to select low/medium/high heat settings for the dryer
• Replaces worn or loose slider that causes inconsistent or stuck temperature selection
• Helps correct symptoms such as inability to change heat level, intermittent temperature changes, or a slider that feels loose or won't stay in position
• Works as the mechanical interface between the console knob/lever and the dryer's control assembly

• One slide temperature control (single slider assembly)

• High-level replacement for users comfortable removing control consoles; disconnect power before service
• Handle control panel clips and trim carefully to avoid cracking plastic bezels
• Verify proper seating and alignment of the slider on the control shaft before reassembly

This temperature control bar is the actuator used to adjust and regulate the appliance's internal temperature, restoring proper temperature response for the bar/beverage control system. It provides a direct replacement for the OEM control bar assembly. What it does:

• Transfers user temperature adjustments to the control mechanism so the appliance reaches the set temperature
• Restores correct temperature changes when the control knob or selector fails to respond
• Helps address symptoms like incorrect temperature readings, temperature not changing, or unstable cooling behavior
• Works with the existing control housing and selector components to re-establish normal operation

• One temperature control bar

• Disconnect power before servicing to avoid electric shock
• Handle the part and surrounding components carefully to avoid damaging clips or wiring
• You may need to remove interior panels or the control housing to access the part;
• Verify the part number on your existing component before installation

This hinge shim adjusts the alignment and spacing of your refrigerator door for proper closure. It ensures the door seals correctly and maintains proper clearance during operation. Replace it if your refrigerator door doesn't close properly, has uneven gaps, or if the door sags and doesn't align with the cabinet.