Kenmore Refrigerator 596.79543010 (59679543010, 596 79543010) Parts

Replace your refrigerator door gasket to restore an airtight seal, maintain temperature, and reduce frost buildup. Confirm fit with your model number.

This replacement motor restores powered rotation to the assembly it drives, bringing smooth, dependable operation back to your appliance. Replacing a weak, noisy, or seized motor can resolve no-run or intermittent performance of the connected function. What it does

• Converts electrical power into controlled shaft rotation to operate the connected mechanism
• Failure signs can include humming or grinding noises, overheating odor, or the feature not starting
• Excess vibration or heat can indicate worn bearings or windings

• 1 motor

• Disconnect power (and shut off water if applicable) before servicing
• Note wire connections and orientation; transfer any brackets, grommets, or attached parts from the original motor if required by your model
• Ensure the shaft spins freely and clearances are correct before reassembly
• Restore power and test; monitor for abnormal noise or heat on first run

Left-side slide bracket that secures and guides drawer assemblies in refrigerators. Replaces worn, cracked, or broken brackets to restore alignment.

Upper freezer glide that supports and guides the freezer drawer for smooth opening and closing. Replaces a worn or damaged glide to help eliminate binding, scraping, and uneven drawer movement. What it does:

• Guides and supports the upper freezer drawer for smooth travel; a failed glide often causes the drawer to stick or catch.
• Reduces metal-on-metal contact and scraping noises when opening or closing the drawer.
• Helps restore proper drawer alignment to prevent uneven gaps or rubbing against the cabinet.
• Lowers stress on adjacent components by returning consistent, even drawer movement.

• Disconnect power to the appliance before beginning any service work.
• Remove freezer contents and the drawer assembly per the manufacturer's instructions to access the glide.
• Replace the glide following the OEM diagram/steps; keep fasteners and mounting points aligned during reassembly.
• Test drawer operation after installation and adjust as needed for smooth, even travel.

Ice maker wiring exposed or damaged? This wire cover shields the harness inside your freezer. Simple snap-in installation takes minutes to secure wiring.

Replaces missing or damaged corner trim filler on your refrigerator. Restores a clean, finished look to interior or exterior cabinet seams and edges.

Left-hand adapter bracket secures and aligns refrigerator components. Replace if your original bracket is cracked, broken, or missing for proper fit.

Right-hand adapter bracket secures and aligns refrigerator panels and components. Replaces worn, damaged, or broken brackets to restore proper fit.

Hex head sheet metal screw secures panels, brackets, and internal components in refrigerators and freezers. Replace missing, corroded, or stripped screws.

Right-hand slide bracket secures drawer or shelf slide assemblies in refrigerators. Replace if cracked, broken, or causing misalignment issues.

Fix loose wiring or rattling sounds in your refrigerator with this terminal block clip kit. Secures harnesses and panels to restore proper fit.

Replaces stripped, missing, or damaged mounting screws that secure panels, brackets, and components in your refrigerator. Restores proper assembly.

Upper door hinge secures and pivots your refrigerator door for smooth operation. Replace if cracked, damaged, or causing door misalignment and gaps.

Wire harness routes power between refrigerator control and components. Replace if wiring is damaged, frayed, disconnected, or causing electrical issues.

Replacement wiring harness for refrigerators. Connects electrical components throughout the unit. Needed when harness is damaged, frayed, or corroded.

This slide temperature control is the user-access interface that moves the thermostat connection to select dryer heat levels. It restores responsive, indexed temperature selection for standard slide-style dryer controls. What it does

• Moves the internal contact to select low/medium/high heat settings for the dryer
• Replaces worn or loose slider that causes inconsistent or stuck temperature selection
• Helps correct symptoms such as inability to change heat level, intermittent temperature changes, or a slider that feels loose or won't stay in position
• Works as the mechanical interface between the console knob/lever and the dryer's control assembly

• One slide temperature control (single slider assembly)

• High-level replacement for users comfortable removing control consoles; disconnect power before service
• Handle control panel clips and trim carefully to avoid cracking plastic bezels
• Verify proper seating and alignment of the slider on the control shaft before reassembly