Kenmore Refrigerator 596.79549011 (59679549011, 596 79549011) Parts

This replacement shim is a thin positioning spacer used to align or level internal components for correct fit and operation. It helps restore proper clearances and reduce rubbing, noise, or misalignment-related issues. What it does:

• Provides precise spacing between parts to ensure correct alignment
• Helps eliminate rubbing or contact that can cause noise or wear
• Restores proper component clearance after service or reassembly
• Used when a missing, worn, or incorrect spacer leads to misalignment symptoms

• One replacement shim

• Inspect mating surfaces and clean debris before installing the shim
• Verify correct placement and orientation against the original shim or diagram
• Tighten fasteners to the manufacturer's specifications; do not overtighten
• Disconnect power and follow all safety precautions before servicing

Sealer for refrigerant line insulation.

This water tank cover replaces a damaged or missing upper reservoir cover to keep the appliance's water reservoir contained and protected. It restores a proper seal and helps prevent water from spilling into internal compartments. What it does:

• Covers and protects the water reservoir to reduce leaks and water intrusion
• Helps maintain correct water flow paths inside the cabinet
• Prevents debris from entering the tank and affecting performance
• Reduces risk of water contacting electrical components or insulation

• One water tank cover

• Designed for drop-in or snap-in replacement; follow OEM diagram for orientation
• Disconnect power and water supply before servicing to avoid shock and leakage
• Inspect adjoining gaskets and mounting clips; replace if cracked or missing
• Handle plastic parts gently to avoid cracking; use appropriate tools to remove fasteners

This cover-tube protects and guides the evaporator/related tubing inside the freezer compartment to help maintain proper airflow and prevent contact damage. It's a direct-fit replacement used in affected Whirlpool refrigeration units. What it does:

• Protects evaporator or refrigerant lines from rubbing, kinking, or accidental contact
• Helps keep tubing routed properly for consistent airflow and cooling performance
• Reduces risk of damage during routine use and service
• Useful when replacing damaged, cracked, or missing tube covers

• Install by sliding or snapping into place per the factory diagram; no adhesives unless specified by OEM
• Power off and unplug the appliance before accessing internal components
• Handle surrounding tubing and evaporator fins carefully to avoid damage

This front pan is the exterior cabinet panel that forms the appliance's front surface, restoring appearance and protecting internal components from dust and debris. It provides a stable mounting surface for the door and control openings. What it does

• Replaces a dented, cracked or rusted front panel to restore the appliance's exterior and fit.
• Protects internal parts from dust, lint and moisture that can enter through a damaged front.
• Helps maintain proper door alignment and sealing when the original front is warped or bent.
• Restores mounting points used for the door, trim and control openings.

• One front pan

• Disconnect power (and water supply if applicable) before starting work.
• Basic hand tools required; installation typically involves removing the door, trim and associated fasteners.
• Keep original screws and brackets if they are undamaged; replace any stripped hardware.

This upper freezer bin provides a roomy, secure shelf for organizing frozen foods and keeping items visible. It replaces a cracked or worn bin so the freezer door stores items safely and tidily. What it does

• Replaces a damaged or broken upper freezer storage bin to restore door storage
• Holds frozen foods and containers to prevent items falling or shifting
• Keeps freezer contents organized and visible for easier access
• Fits into the designated upper freezer door slot and supports normal use

• One upper freezer bin

• Remove frozen items and open the freezer door fully before replacing the bin
• Slide the old bin out gently and align the new bin with the door tracks until it clicks into place
• No special tools usually required; handle with care to avoid cracking the new plastic

This self-drilling screw secures appliance panels and components where a fastener must cut its own pilot hole. It provides a quick, reliable hold for repair or reassembly of trim, brackets, and internal fixtures. What it does:

• Fastens panels, brackets, and small components without pre-drilling
• Helps stop loose or rattling trim and parts caused by missing or worn screws
• Restores proper alignment and secure mounting after repairs
• Works where sheet metal or thin substrates require self-tapping engagement

• One self-drilling screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct size driver and steady pressure to avoid stripping the head
• Start straight and apply firm, even torque; avoid overtightening which can damage mounting surfaces
• Wear eye protection and handle small fasteners carefully to avoid loss or ingestion hazards

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

Size: 3/16 inch.

Size: 5/16 inch.

Size: 3/8 inch.

Size: 3/4 inch.

This mounting bracket secures and supports internal appliance components to keep assemblies aligned and reduce vibration. A simple replacement that restores proper fit and stops rattling or loose panels caused by a broken or bent bracket. What it does

• Provides a rigid anchor point to hold panels, assemblies or hardware in place
• Keeps components aligned to prevent rubbing, vibration and noise
• Restores proper fit where a worn or damaged bracket caused gaps or looseness
• Helps maintain safe operation by preventing parts from shifting during use

• One mounting bracket

• Disconnect power (unplug appliance or turn off circuit) before starting any repair
• Basic hand tools (screwdriver, nut driver) typically required; retain removed fasteners for reassembly
• Handle edges carefully; metal parts may be sharp
• for exact bracket location and proper reassembly

This bale strap is a direct-replacement part that helps secure the dryer's latch/bale assembly so the door closes and stays closed during operation. Replacing a worn or broken strap restores reliable door engagement and safer drying cycles. What it does:

• Anchors the dryer door's latch/bale so the door remains properly closed during operation
• Prevents intermittent door opening that can stop cycles or cause heat loss
• Replaces a stretched, torn, or broken strap that no longer holds the latch securely
• Works with the door/latch mechanism to maintain safe operation during drying

• One bale strap

• Disconnect power before beginning any repair to avoid electrical shock
• Verify strap routing and attachment points match the original before reinstalling
• Basic hand tools are typically required; avoid forcing plastic clips to prevent breakage