Kenmore Refrigerator 596.79553011 (59679553011, 596 79553011) Parts

Seals the drain tube connection to prevent leaks and ice buildup in your freezer. Replace if you see water pooling or ice forming at the freezer bottom.

This limit switch is a temperature safety device that opens the circuit if heat rises too high. Replacing a weak or failed switch restores proper overheat protection and can resolve nuisance shutdowns or no-heat conditions due to an open safety. What it does:

• Monitors temperature at its mounting location
• Opens the electrical circuit at a preset over-temperature to stop heating or operation
• Helps protect internal components and wiring from heat damage
• Common symptoms include: won't heat, shuts off during use, or no power after an overheat event

• 1 limit switch

• Disconnect power (and gas, if applicable) before servicing
• Access the switch, note wire positions, and transfer wires one at a time
• Mount the switch flat and firmly against the original sensing surface or bracket
• After replacement, check for root causes of overheating (blocked airflow, failed fan, dirty filters, shorted element)

Supports and guides your refrigerator's drawer for smooth, aligned travel. Replace if drawer sticks, sags, or derails. Verify fit with your model number.

Factory screw that secures panels, brackets, and hardware inside your refrigerator. Replace missing or stripped screws to eliminate rattles and loose fits.

Replace your refrigerator door gasket to restore an airtight seal, maintain temperature, and reduce frost buildup. Confirm fit with your model number.

Fixes blank displays, unresponsive controls, or erratic cooling cycles. This control board directs refrigerator power and responds to user commands.

Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Ice maker not filling or leaking? This water tube routes water from the inlet to the ice maker fill valve. Replaces cracked or clogged tubing in your fridge.

Size: 8 x 1-1/4 inch.

This is a trim piece that serves as a guide for the refrigerator door flapper or breaker strip, helping to direct airflow and ensure a proper seal between compartments. It mounts near the door opening and keeps the flapper aligned correctly. Replace this part if the guide is cracked, broken, or missing, which can lead to cold air escaping and temperature inconsistencies inside the refrigerator.

Plastic cover that protects and supports the damper assembly in your refrigerator. Replace if cracked, broken, or missing to keep airflow components secure.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This user interface control board manages the oven's front-panel display and touch controls so you can select functions, set temperatures and start cycles. Replacing a failed UI board restores normal control and display feedback. What it does:

• Receives and processes inputs from the touchpad or buttons so selections start the correct cycles
• Drives the front-panel display and indicator lights for cycle status and settings
• Communicates commands to the main control to trigger heating and timing operations
• Fault symptom coverage: blank or unresponsive display, unresponsive touchpad/buttons, or incorrect front-panel behavior

• One user interface control board

• Disconnect power at the breaker before starting any repair to prevent shock
• Handle the board by edges and avoid touching components; observe anti-static precautions
• Verify connectors are fully seated but do not force; match connector shapes and pin counts

This bracket provides structural support for refrigerator drawers on the left side, helping them slide smoothly and remain stable. Located inside the refrigerator on the left interior wall, replace it when drawers sag, won't slide properly, or become loose and unstable.

Replacement ice bin for bottom-mount refrigerators. Stores ice from the icemaker and fits in the freezer compartment. Replace if cracked or broken.