Kenmore Dishwasher 665.13272K110 (66513272K110, 665 13272K110) Parts

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This brace connector secures a support brace inside the appliance to help keep internal panels and assemblies aligned and stable. Replacing a worn or damaged connector restores proper support and reduces noise and movement. What it does:

• Fastens and stabilizes an internal support brace or frame
• Prevents panel or assembly movement that can cause vibration or rattling
• Helps maintain proper alignment of connected components
• Replaces broken or corroded connector hardware to restore secure mounting

• One brace connector

• Disconnect power (and gas, if applicable) before starting any repair
• Access may require removing outer or control panels; save existing fasteners for reuse
• Use basic hand tools; avoid overtightening to prevent cracking plastic or bending metal
• Inspect and replace as needed

This tube nut secures the water inlet tubing to its fitting, creating a tight, leak-resistant connection. Use it when the original nut is cracked, stripped, or can no longer hold the line securely.

• Tightens over the inlet fitting to clamp the water tube and form a reliable seal
• Helps stop drips at the water-line connection point
• Addresses loose or damaged inlet connections and difficulty keeping the tube seated
• Commonly replaced when the nut is worn, cross-threaded, or visibly cracked

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Hold the fitting with one wrench while tightening the nut with another to avoid twisting components
• Do not overtighten; restore water and check for leaks after installation
• Inspect the tubing, ferrule/sleeve, and insert; replace if worn or damaged

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This mounting stud secures appliance panels and components to the cabinet, restoring proper fit and stability. Durable metal construction replaces a damaged or missing stud to keep panels aligned and reduce rattling. What it does:

• Fastens panels, trim, or components to the appliance cabinet for a secure fit
• Restores correct panel alignment to prevent gaps and vibration noise
• Replaces stripped, bent, or missing studs that prevent proper assembly
• Works with the cabinet/frame mounting points used by the original hardware

• Inspect mating threads and holes for damage before installation; replace damaged fasteners as needed
• Hand-start the stud to avoid cross-threading, then tighten with appropriate tool; do not overtighten
• Disconnect power to the appliance before doing any repairs that expose electrical components

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit

This console housing is the outer bezel that holds and protects the user interface and control components on the appliance. It restores a secure mounting surface for buttons, touch pads, and the display for reliable operation. What it does:

• Provides the structural mounting and protection for the control board, display and keypad
• Keeps buttons and touch controls aligned for correct operation
• Prevents dirt and moisture from reaching electronic components
• Commonly replaced when the console is cracked, broken or loose

• One console housing

• Disconnect power to the appliance before starting any repairs
• Handle electronic components and ribbon cables carefully to avoid damage
• You may need basic hand tools to remove the existing console and fasteners

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This vent door bezel covers and directs exhaust airflow at the appliance vent opening, helping maintain proper venting and preventing large debris from entering the duct. Replacement restores correct vent closure and airflow path. What it does:

• Covers the external vent opening and guides exhaust air away from the appliance
• Helps prevent large debris, pests, and items from entering the vent
• Restores a properly closing vent flap that can reduce backflow and improve venting
• Worn, broken, or stuck vent bezel can cause reduced air exhaust or visible gaps at the vent opening

• Disconnect power (and gas if applicable) before starting any repair
• Inspect surrounding seals and mounting tabs; replace if damaged to ensure a proper fit
• Handle plastic parts carefully to avoid cracking; use proper fasteners and torque to OEM specs

This replacement silverware basket sits in the dishwasher rack and keeps forks, knives, and spoons upright and contained so they wash thoroughly and don't slip through the rack or interfere with spray-arm movement. What it does:

• Holds and organizes flatware during wash and rinse cycles
• Helps separate utensils for better spray coverage and drainage
• Replaces cracked, warped, or missing baskets

• 1 silverware basket

• Open the dishwasher and pull out the lower rack for access
• Lift out the old basket and place the new basket in the same location/orientation
• Ensure the basket seats securely and does not contact the lower spray arm
• Manually spin the spray arm to confirm clearance before running a cycle