Kenmore Dishwasher 665.13272K110 (66513272K110, 665 13272K110) Parts

The Seal is an OEM part for Whirlpool dishwashers. As a crucial door component, it ensures a tight fit that prevents leaks and contains the necessary heat and moisture during operation. 

Symptoms of a bad seal can include cracks, tears, or looseness allowing water to escape during cycles. Deterioration from chemical exposure or repeated flexing over time is common.

Causes of a bad seal include general wear and tear, damage from improper loading of dishes, or accidents like sharp objects puncturing the material.

Symptoms of a bad seal include: 

• Puddles or pools of water found beneath the dishwasher after cycles
• Wet floors and surfaces surrounding the dishwasher  
• Steam or moisture visible escaping during heating phases
• The door not closing or latching properly

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This control panel is the console assembly that houses the user controls and display, restoring full interface function and reliable selection of cycles and options on compatible Whirlpool laundry units. What it does

• Replaces the main user interface so buttons, touch controls, and the display respond correctly.
• Restores cycle selection, start/pause, and option controls when the original console is faulty.
• Common symptoms it fixes: unresponsive buttons, blank or flickering display, incorrect or no input response.
• Also replaces consoles damaged by cracks, wear, or moisture that affect operation.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Handle display and ribbon cable connectors carefully to avoid damage.
• Removal typically requires access to the washer/dryer front console and simple hand tools.

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This electronic control board is the appliance's central controller. It interprets user inputs and sensor signals to power components at the right time, restoring reliable operation when the original board fails.

• Interprets user settings and manages cycle timing and temperature control
• Switches relays/outputs to run motors, heaters, valves, fans, and lights
• Interfaces with sensors and safety switches to protect the appliance
• Symptoms can include no display or response, won't start, cycles that won't advance, or erratic operation
• Logs diagnostic error codes to aid troubleshooting

• Disconnect power before servicing; follow ESD precautions and handle the board by the edges
• Access the control area, then note/photograph wiring and move connectors one at a time to the new board
• Mount securely, ensure no wires are pinched, reassemble, and restore power
• Run a diagnostic or test cycle to confirm normal operation

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Color: White

This replacement wheel installation leg restores mobility and stable support for appliances that use a leg-mounted rolling wheel. It provides a direct-fit restore of worn or damaged legs to help move and position the appliance safely. What it does

• Replaces a damaged or worn wheel-style leg that supports and helps roll the appliance
• Restores smooth rolling and stabilizes appliance during movement
• Helps resolve symptoms like a broken/collapsed leg, stuck wheel, or uneven appliance height
• Matches OEM form and fit for direct replacement when the original leg/wheel is worn

• One wheel installation leg

• Turn off and unplug the appliance and remove contents or shelves as needed before working underneath
• Use basic hand tools; avoid forcing components—reuse existing fasteners

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This replacement silverware basket sits in the dishwasher rack and keeps forks, knives, and spoons upright and contained so they wash thoroughly and don't slip through the rack or interfere with spray-arm movement. What it does:

• Holds and organizes flatware during wash and rinse cycles
• Helps separate utensils for better spray coverage and drainage
• Replaces cracked, warped, or missing baskets

• 1 silverware basket

• Open the dishwasher and pull out the lower rack for access
• Lift out the old basket and place the new basket in the same location/orientation
• Ensure the basket seats securely and does not contact the lower spray arm
• Manually spin the spray arm to confirm clearance before running a cycle