Kenmore Compactor 665.1330590 (6651330590, 665 1330590) Parts

This wave washer is a small, wavy metal retainer that holds rotating or sliding components in place on a shaft. It helps maintain proper alignment and reduces end-play for smoother, quieter operation. What it does:

• Secures components on a shaft to prevent axial movement and maintain alignment
• Helps reduce vibration and rubbing that can cause noise or premature wear
• Commonly used behind agitator, cam, or bearing assemblies where axial retention is required
• Replace if the washer is deformed, cracked, or missing to restore correct component spacing

• Disconnect power before starting repairs
• Remove the affected assembly (agitator/shaft or other specified part) to access the washer
• Install the washer in the same orientation and position as the original; ensure it seats fully
• Inspect surrounding components (bushings, seals, bearings) and replace any worn parts to prevent repeat failure

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

Size: 6-32 x 3/8 inch.

This C-shaped retaining ring snaps into a groove on a shaft or pin to hold a component in place. It restores secure retention so parts don't slide off or shift during operation.

• Snaps into a groove to secure parts on a shaft or pin
• Prevents axial movement to keep assemblies aligned
• Helps reduce wobble, rattling, or parts migrating off
• Common signs: missing/broken clip, loose mechanisms, parts slipping off during use

• Disconnect power; also shut off water or gas as applicable
• Wear eye protection—retaining clips can spring free during removal/installation
• Use appropriate snap/retaining ring pliers or a small flat tool; avoid over-expanding the ring
• Ensure the ring seats fully in the groove and replace if bent or fatigued

A small slotted pin spring used to secure moving parts in appliance assemblies. This compact replacement restores proper retention and alignment where a slotted spring pin is required, helping moving parts stay in place and operate smoothly. What it does:

• Acts as a slotted spring pin to hold shafts, levers or clips in position
• Restores secure retention when original pin is bent, worn or missing
• Prevents excess play or disengagement of connected components
• Helps resolve symptoms like loose or shifting parts, rattling, or components not staying engaged

• One slotted pin spring

• High-level replacement; retains existing mating hardware and holes
• Use proper tools (needle-nose pliers, punches) to remove/install without damaging surrounding parts
• Wear eye protection; pins can release under tension during removal

This flat metal washer provides a durable spacer and load-bearing surface for fasteners in the appliance, helping maintain proper alignment and reduce wear on mating parts. It's a simple replacement that restores correct assembly spacing. What it does:

• Acts as a load-distributing spacer between fastened components to prevent loosening and wear
• Helps maintain proper alignment of shafts, housings, or assemblies
• Can reduce vibration or movement caused by uneven mating surfaces
• Commonly replaced when hardware is corroded, damaged, or missing

• One flat metal washer (quantity: 1)

• Verify the exact washer size and thickness before installation; replace with the same type
• Tighten fasteners to the manufacturer's torque specifications when known; avoid overtightening
• If used near electrical connections, ensure power is disconnected before working
• Inspect adjacent fasteners and components for wear and replace if necessary

The Drive Gear Kit is an OEM replacement part for Whirlpool trash compactors. It is an essential component that powers the compaction mechanism. The drive gear kit consists of a series of gears, shafts, and other components that work together to transfer the motor's rotational force to the compaction ram.

Causes of a bad drive gear kit in a trash compactor can include mechanical wear and tear over time, exposure to excessive loads or foreign objects, or damage from improper usage or maintenance.

Symptoms of a faulty drive gear kit in a trash compactor:

• Difficulty in starting or completing the compaction cycle
• Loud grinding or squeaking noises during operation
• Failure of the compaction ram to move or compress waste properly
• Leaks or vibrations due to improper alignment or gear damage

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore trash compactor models.

This black refrigerator container handle replaces a worn, cracked, or missing pull on an interior bin or drawer. It restores a secure grip so you can easily slide the container in and out on compatible models.

• Attaches to the front of a refrigerator container or its cover to provide a solid handhold
• Replaces cracked, loose, or missing handle pieces
• Helps bins open and close smoothly without stressing the cover/front
• Common symptoms: handle broken or missing, tabs snapped, handle won't stay attached, drawer hard to pull

• Remove the bin/drawer and place the cover or front on a flat, protected surface
• Release the old handle by removing screws or disengaging tabs/clips (varies by model); keep hardware for reuse
• Align the new handle and snap or screw it into place; do not overtighten
• Handle glass and plastic parts carefully; wearing cut-resistant gloves is recommended

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This replacement leveling wheel restores a dryer/washer cabinet's ability to sit level and roll smoothly during adjustment. It helps stop wobble and ensures the appliance can be properly leveled for stable operation. What it does:

• Replaces a worn or broken leveling wheel on the appliance base or leveling assembly
• Allows the cabinet to be adjusted up or down when setting appliance height
• Helps reduce rocking, uneven vibration, and unstable operation caused by a damaged leveler
• Works with the appliance's leveling hardware to keep the cabinet properly supported

• One replacement leveling wheel

• Disconnect power and water before beginning any work
• Support the appliance securely to relieve weight from the leveling assembly before removal
• Remove the old wheel from the leveler shaft and press or snap the new wheel into place; use basic hand tools as needed

This retainer bracket secures internal components in place to restore proper alignment and support. It replaces a worn or broken bracket to help reduce rattling, misalignment, or loose parts during operation. What it does:

• Holds and supports internal assembly parts to maintain correct positioning
• Prevents movement that can cause noise, vibration, or rubbing
• Restores stability after bracket damage or wear
• Works as a direct-fit replacement when the original bracket is broken or bent

• High-level replacement — basic hand tools required;
• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding parts and hardware; replace any damaged fasteners for a secure fit

Bag carrier handle assembly that secures a disposable dust bag to the vacuum housing, letting you remove and replace bags cleanly and safely. Restores proper bag seating and handling for bagged vacuum units. What it does:

• Holds the dust bag in place so debris is directed into the bag, not the housing
• Provides a grip for removing and carrying full bags without tearing or spillage
• Replaces a cracked, broken, loose, or missing handle that prevents proper bag seating
• Helps stop bag detachment or leaks caused by an unstable carrier

• Always unplug the appliance before servicing.
• Remove the old bag and carrier, noting orientation; the carrier may snap into place or be secured with small screws.
• Verify the new carrier seats and latches fully before installing a new bag.

This small conical washer is used in select washer assemblies to maintain clamp force under vibration. It helps keep fasteners tight and components properly aligned for reliable wash and spin performance. What it does:

• Provides spring-like tension under a screw or bolt to maintain clamp load
• Helps prevent fasteners from loosening due to vibration
• Supports proper alignment and secure fit of mating parts
• Worn or missing washers can lead to rattling, looseness, or intermittent operation

• 1 cone washer

• Disconnect power and, if applicable, turn off water supply before servicing
• Access the relevant assembly per your model's service information
• Note the washer's original orientation and match it during reassembly
• Tighten hardware securely without over-torquing; test and recheck for security

This sprocket is the replacement drive gear that helps transfer motor movement to the appliance's drive system, restoring reliable rotation and timing. It's a direct-fit component used in the unit's drivetrain to maintain proper mechanical engagement. What it does:

• Engages with the drive chain/belt or related components to transmit rotational force from the motor
• Maintains proper timing and alignment of moving parts for consistent operation
• Worn or broken sprockets can cause skipping, slipping, noisy operation, or loss of drive
• Replacing a damaged sprocket helps eliminate drivetrain play and irregular movement

• One sprocket

• Disconnect power (and water supply if applicable) before beginning any repair
• Inspect mating components (chain/belt, bearings, bushings) and replace if worn to prevent premature failure
• Installation may require basic hand tools and lifting or support of the assembly; follow the appliance service manual for disassembly/reassembly steps

This is a rotary control knob that replaces a worn or broken selector knob to restore accurate, tactile control of your appliance settings. It snaps onto the control shaft for a secure fit and easy operation. What it does:

• Allows you to turn and select appliance settings smoothly and reliably
• Restores a damaged, cracked, or missing knob that makes setting changes difficult
• Provides a firm grip for precise control and improved user confidence
• Helps eliminate slipping or loose rotation when the original knob is worn

• Pull the old knob straight off the control shaft; push the replacement fully onto the shaft until seated
• No special tools typically required; use gentle, steady force to avoid damaging the shaft
• Disconnect power to the appliance before removing panels or working near energized controls