Kenmore Compactor 665.1340594 (6651340594, 665 1340594) Parts

This ram stop is a small control component used in the ram assembly of trash compactors. It limits ram travel so the compactor stops at the correct position and the drawer opens smoothly after each cycle.

• Limits the upward travel of the ram to a fixed stop point
• Helps the ram return fully to the up position at the end of the cycle
• Reduces binding and prevents over-travel that can strain components
• Typical symptoms include a drawer that won't open or is hard to open, or a ram that doesn't return to the top

• Disconnect power to the compactor before servicing
• Remove the drawer/bin for access and support the ram
• Remove the damaged stop and install the replacement, ensuring it is fully seated and correctly oriented
• Run an empty test cycle to confirm the ram stops at the proper height

Almond. Size: 13 oz. can. Acrylic appliance paint.

This switch nut secures a rotary control or switch to the appliance's front panel. Replacing a stripped or missing nut keeps the control stable so the knob turns smoothly and the shaft stays properly aligned.

• Clamps the switch/control to the panel to prevent movement or rotation
• Helps maintain correct knob alignment with dial markings
• Common symptoms: loose or wobbly knob, switch rotates in the panel, missing/damaged nut
• Often needed after service if the original nut is stripped or lost

• Disconnect electrical power before servicing
• Remove the knob and any decorative escutcheon; thread the new nut onto the switch bushing from the front of the panel
• Support the switch from behind while tightening; do not overtighten to avoid panel or switch damage
• Restore power and test control operation

This replacement stud is a factory-specified piece of hardware used to secure components in your appliance. Replacing a worn, stripped, or missing stud restores a solid fit to help reduce looseness and vibration. What it does:

• Provides a mounting point to fasten specified parts or panels
• Helps keep components aligned and secure during operation
• Replaces damaged, corroded, or missing original hardware
• Can resolve symptoms like loose parts, rattling, or misalignment where this fastener is used

• 1 stud

• Disconnect power; shut off water and/or gas supply if applicable
• Access the mounting location per your model's service information
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or nuts if required and in good condition

Color: Almond

This Inner Door Panel forms the interior surface of the dishwasher door. Replacing a dented or corroded panel restores proper sealing and structural support for the latch and dispenser, helping prevent leaks and rattling during wash cycles.

• Creates the interior door surface and directs water back into the tub
• Provides mounting points for the detergent/rinse aid dispenser, door latch, and vent components
• Helps maintain a watertight seal when the door is closed
• Replace if rusted, cracked, warped, or if dispenser/latch mounts are broken; may show leaks at the door or unusual rattling

• Disconnect power and water supply before servicing
• Open the door and remove perimeter screws; support the outer door panel as you separate the panels
• Transfer the dispenser, latch, vent, and any insulation/gaskets from the old panel to the new panel
• Reassemble with even screw torque; verify door closes/seals and run a short test cycle to check for leaks

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet motion. Replacing a worn bearing helps eliminate noise, restore proper alignment, and prevent damage to mating parts.

• Supports and centers a rotating shaft or hub
• Reduces friction and wear for smoother, quieter operation
• Helps maintain alignment of connected components
• Common failure symptoms: grinding or squealing sounds, vibration or wobble, rough/stiff or seized rotation, excessive play

• Disconnect power before servicing; shut off water or gas if applicable
• Note orientation and retaining hardware before removal
• Use proper tools (puller/press) to remove and seat the bearing squarely—avoid hammering
• Inspect shaft/bore and related seals or spacers; replace worn components before reassembly

Size: 3\8-24 inch.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

A replacement screw used to secure the appliance power connection for reliable electrical contact and safe operation. Restores a solid connection if the original screw is missing, loose, or damaged. What it does:

• Secures the power terminal/cord or related power assembly to maintain consistent electrical contact.
• Helps prevent intermittent power, arcing, or overheating caused by loose or damaged fasteners.
• Replaces a missing, stripped, or corroded screw so the appliance can operate safely and reliably.

• Always disconnect power to the appliance before starting any repair.
• Use the correct screwdriver and thread engagement; avoid overtightening to prevent stripped threads or damaged terminals.
• Inspect adjacent wiring, terminals, and the cord strain relief; replace any damaged components.

Power screw hub is a replacement drive hub that secures the washer's drive screw/agitator to the transmission, helping restore proper agitation and reduce slipping. Fits applications where a worn or broken hub causes drive loss. What it does:

• Transfers rotational force from the drive screw/agitator to the transmission so the washer can agitate or spin.
• Replaces stripped or worn splines that allow the agitator or drive screw to slip under load.
• Common symptoms it can help fix: agitator or drum won't engage, intermittent agitation, grinding or squeaking during cycles.
• Install replacement if splines are visibly damaged or if the hub no longer holds the drive assembly securely.

• Disconnect electrical power (and water supply if applicable) before beginning any repair.
• Remove agitator/drive components; use the correct tools to avoid further spline damage.
• Inspect mating splines and fasteners; replace any damaged hardware and clean the area before installation.
• After reassembly, run a short test cycle to confirm normal operation.

Size: 10-24 x 3/8 inch.

This is the left side frame slide. For right side use W11722978.

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

This mount plate is a stamped metal bracket that secures a component inside the appliance, helping keep parts aligned and reducing movement. Replace a damaged or bent plate to restore a stable, secure installation. What it does:

• Provides a stable mounting point for internal components to prevent shifting or sagging
• Helps reduce vibration and rattling caused by loose or worn mounting surfaces
• Keeps electrical and mechanical parts properly aligned for reliable operation
• Common symptom: visible looseness, noise, or component movement during use

• Disconnect power and unplug the appliance before starting any repair
• Verify the plate orientation and mounting hole alignment with your appliance's service diagram
• Use the original screws or OEM-specified fasteners and tighten securely but do not overtighten