Kenmore Compactor 665.1350195 (6651350195, 665 1350195) Parts

Conical washer for trash compactor assemblies. Maintains tension under screws or bolts to keep components aligned. Replace if worn, cracked, or missing.

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

Fix parts sliding off shafts or shifting during compaction. This C-ring snaps into grooves to secure components and prevent axial movement in your compactor.

Size: 6-32 x 3/8 inch.

A deodorizer designed to neutralize odors inside a trash compactor. It attaches inside the compactor compartment to help control smells from compressed waste. Replace when the deodorizer loses effectiveness and persistent odors return despite regular cleaning.

Size: 8-32 x 1/4 inch.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

Protective shield for trash compactor slide track assembly. Replace if cracked, broken, or missing to protect the track mechanism and ensure smooth operation.

Holds compactor bags securely during operation. Replace if cracked, broken, or handles are damaged. Installs inside compactor drum for easy bag removal.

For use on power screw and ram pressure pads. Size: 4 oz. can.

This is a black plastic handle that attaches to the front of the trash compactor drawer, allowing you to pull the drawer open and push it closed. It serves as the primary grip point for operating the compactor's waste drawer. Replace this handle if it is cracked, broken, or if the mounting tabs have snapped off, making it difficult to open or close the drawer.

A replacement screw used to secure the appliance power connection for reliable electrical contact and safe operation. Restores a solid connection if the original screw is missing, loose, or damaged. What it does:

• Secures the power terminal/cord or related power assembly to maintain consistent electrical contact.
• Helps prevent intermittent power, arcing, or overheating caused by loose or damaged fasteners.
• Replaces a missing, stripped, or corroded screw so the appliance can operate safely and reliably.

• Always disconnect power to the appliance before starting any repair.
• Use the correct screwdriver and thread engagement; avoid overtightening to prevent stripped threads or damaged terminals.
• Inspect adjacent wiring, terminals, and the cord strain relief; replace any damaged components.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

Metal mounting bracket that secures internal components in your trash compactor. Replace if bent, damaged, or missing to restore stable part alignment.

Secures and supports internal compactor components to keep panels and assemblies aligned. Replaces worn, damaged, or missing brackets for firm installation.