Kenmore Compactor 665.13603000 (66513603000, 665 13603000) Parts

White plastic foot pedal for trash compactors. Installs at base of unit to release door latch. Replace if cracked, broken, or no longer springs back.

Size: 10-24 x 3/8 inch.

A replacement screw used to secure the appliance power connection for reliable electrical contact and safe operation. Restores a solid connection if the original screw is missing, loose, or damaged. What it does:

• Secures the power terminal/cord or related power assembly to maintain consistent electrical contact.
• Helps prevent intermittent power, arcing, or overheating caused by loose or damaged fasteners.
• Replaces a missing, stripped, or corroded screw so the appliance can operate safely and reliably.

• Always disconnect power to the appliance before starting any repair.
• Use the correct screwdriver and thread engagement; avoid overtightening to prevent stripped threads or damaged terminals.
• Inspect adjacent wiring, terminals, and the cord strain relief; replace any damaged components.

Conical washer for trash compactor assemblies. Maintains tension under screws or bolts to keep components aligned. Replace if worn, cracked, or missing.

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

Secures and supports internal compactor components to keep panels and assemblies aligned. Replaces worn, damaged, or missing brackets for firm installation.

Left side frame slide for trash compactors. Replaces cracked, broken, or worn slides that support the compactor drawer. Essential structural component.

Fix parts sliding off shafts or shifting during compaction. This C-ring snaps into grooves to secure components and prevent axial movement in your compactor.

Slotted pin spring secures moving parts in trash compactor assemblies. Replace if worn, missing, or damaged to restore proper retention and alignment.

Size: 6-32 x 3/8 inch.

Size: 8-32 x 1/4 inch.

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

Touch up paint for appliances with chips, scratches, or worn spots. Includes brush applicator. Restores finish on damaged surfaces. 0.6 fl oz.

Replacement foot pedal for trash compactors. Operates the compacting mechanism when pressed. Replace if cracked, broken, or missing for proper operation.

A deodorizer designed to neutralize odors inside a trash compactor. It attaches inside the compactor compartment to help control smells from compressed waste. Replace when the deodorizer loses effectiveness and persistent odors return despite regular cleaning.

Replacement screw that secures panels, covers, brackets, and trim to appliance frames. Needed when original screws are stripped, missing, or damaged.