Kenmore Compactor 665.1398180 (6651398180, 665 1398180) Parts

Conical washer for trash compactor assemblies. Maintains tension under screws or bolts to keep components aligned. Replace if worn, cracked, or missing.

Drive sprocket for trash compactor power screw assembly. Replaces worn, broken, or stripped gear that transfers motor power to the drive system.

This retainer bracket secures internal components in place to restore proper alignment and support. It replaces a worn or broken bracket to help reduce rattling, misalignment, or loose parts during operation. What it does:

• Holds and supports internal assembly parts to maintain correct positioning
• Prevents movement that can cause noise, vibration, or rubbing
• Restores stability after bracket damage or wear
• Works as a direct-fit replacement when the original bracket is broken or bent

• High-level replacement — basic hand tools required;
• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding parts and hardware; replace any damaged fasteners for a secure fit

Drive chain connects the motor to the ram mechanism in your trash compactor. Replace if the chain is broken, stretched, or missing to restore compaction function.

Touch up paint for appliances with chips, scratches, or worn spots. Includes brush applicator. Restores finish on damaged surfaces. 0.6 fl oz.

Compactor won't run unless you hold the dial? A worn safety switch actuator prevents proper door latch engagement. This repair restores automatic operation.

This deodorant is a replacement refrigerator deodorizer that helps reduce common food and household odors inside the fresh-food compartment for a cleaner-smelling interior. Simple swap helps maintain a neutral-smelling refrigerator. What it does:

• Adsorbs and reduces odors in the refrigerator interior to help keep food-smelling fresher
• Fits into the refrigerator deodorizer holder or designated compartment
• Works passively—no power or batteries required
• Helps refresh interior air between routine cleaning cycles

• For best results, remove old deodorizer and place new cartridge in the designated holder
• Disconnect power before beginning
• Wash hands after handling and follow local disposal guidelines for used cartridges
• If odors persist, inspect seals, drains, and spoiled food before replacing the deodorizer

Appliance won't start or trips breaker? This ground screw secures the grounding conductor to the chassis for safe electrical connection. Simple fix.

Size: 6-32 x 3/8 inch.

Fix parts sliding off shafts or shifting during compaction. This C-ring snaps into grooves to secure components and prevent axial movement in your compactor.

Slotted pin spring secures moving parts in trash compactor assemblies. Replace if worn, missing, or damaged to restore proper retention and alignment.

Size: 8-32 x 1/4 inch.

This black refrigerator container handle replaces a worn, cracked, or missing pull on an interior bin or drawer. It restores a secure grip so you can easily slide the container in and out on compatible models.

• Attaches to the front of a refrigerator container or its cover to provide a solid handhold
• Replaces cracked, loose, or missing handle pieces
• Helps bins open and close smoothly without stressing the cover/front
• Common symptoms: handle broken or missing, tabs snapped, handle won't stay attached, drawer hard to pull

• Remove the bin/drawer and place the cover or front on a flat, protected surface
• Release the old handle by removing screws or disengaging tabs/clips (varies by model); keep hardware for reuse
• Align the new handle and snap or screw it into place; do not overtighten
• Handle glass and plastic parts carefully; wearing cut-resistant gloves is recommended

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.