Kenmore Dishwasher 665.1544590 (6651544590, 665 1544590) Parts

Float that detects and communicates water level to the appliance control so the washer or dishwasher can fill and drain properly. Replaces a cracked, stuck, or worn float to restore reliable water sensing. What it does:

• Senses water level and relays position to the machine's control system.
• Helps prevent overfilling or unintended continuous filling when working correctly.
• Can resolve symptoms such as flooding, constant filling, no fill, or improper drain cycles.
• Works with the appliance's existing valve and switch components to re-establish normal fill/drain operation.

• Disconnect power (and water supply where applicable) before beginning service.
• Remove outer panels or tub shroud to access the float; use basic hand tools.
• Handle clips and fittings gently; do not force plastic tabs or connectors during removal/installation.
• After installation, restore power and run a test cycle to ensure correct fill and drain behavior.

This package contains one roller. To order a set of 4 use 4317933.

This seal collector is a molded collector seal that helps contain and direct water away from sensitive components, reducing leaks and moisture damage. It replaces a worn or cracked collector seal to restore normal water containment. What it does

• Channels and contains water at the tub/door interface to prevent leaks
• Replaces torn, hardened, or deformed seals that allow moisture escape
• Helps prevent water from reaching electrical components and undercarriage
• Commonly replaced when visible gaps, cracks, or persistent leaks are present

• One seal collector

• Disconnect power and water before starting any repair
• Access may require removing the door, kick panel, or access panels depending on model
• Inspect mating surfaces and clean debris before installing the new seal for proper fit

Color: White. Size: 13 oz. Spray paint primer. can.

This disk mount is a small replacement mounting disk that secures and aligns internal components so the appliance operates quietly and reliably. It restores proper fit where a worn or damaged mount causes misalignment or vibration. What it does:

• Provides a secure mounting point for internal assemblies and helps maintain correct component alignment
• Reduces vibration and rattling caused by a broken or deteriorated mount
• Supports stable operation and prevents excess wear on adjoining parts
• Commonly replaced when mount is cracked, warped, or missing

• One disk mount as shown

• Basic hand tools typically required; inspect surrounding components for damage before reassembly
• Disconnect power and/or gas and follow appliance safety procedures before starting work
• Retain all fasteners and observe correct orientation during installation

This door spring provides the tension needed for proper door operation and restores smooth opening and closing. It replaces a worn or broken spring to help the appliance door stay aligned and operate quietly. What it does:

• Supplies tension to the door assembly so the door opens and closes smoothly
• Helps the door stay properly aligned and close securely
• Can prevent sagging or uneven door movement caused by a weakened spring
• Reduces rattling or noisy operation related to a worn door tension spring

• Disconnect power to the appliance before attempting any repair to avoid electrical shock
• Release stored tension carefully; springs can snap back and cause injury—use appropriate tools and eye protection
• Verify correct spring orientation and seating during reassembly to ensure proper door function

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This support bearing assembly stabilizes the dryer drum and helps it spin smoothly to improve tumbling and reduce noise. Designed to replace a worn or noisy rear drum support for compatible Whirlpool dryers. What it does:

• Supports the rear of the dryer drum so it rotates evenly
• Reduces squeaks, grinding, and wobbling caused by worn bearings
• Helps maintain proper drum alignment to prevent uneven wear
• Works with the drum shaft to keep tumbling smooth during operation

• One support bearing assembly

• Disconnect power before beginning any repair to avoid electrical shock
• Access may require removing the dryer rear panel and drum; follow manufacturer service instructions
• Inspect adjacent components and replace if excessively worn
• Tighten fasteners to manufacturer torque specs and test operation after reassembly

This flexible replacement hose routes water safely in your appliance to restore normal water flow and prevent leaks. It replaces a worn, cracked, or leaking factory hose so your appliance can operate reliably. What it does:

• Carries water between components to maintain proper appliance operation
• Helps stop leaks caused by brittle, cracked, or damaged hoses
• Compatible with original mounting and connection points when replacing the same part number
• Common symptom: visible leaks, reduced water flow, or water pooling near the appliance

• Turn off power and shut off water supply before attempting replacement
• Inspect fittings and clamps; reuse only if undamaged, otherwise replace with proper hardware
• Ensure secure, leak-free connections and verify no kinks in the hose after installation

Split-ring seal designed to secure a door or panel gasket and maintain a watertight/airtight joint, helping stop leaks and keep the appliance operating properly. Ideal for replacing worn or damaged seals. What it does:

• Holds and seals the gasket or trim in place to prevent water or air from escaping.
• Restores a tight seal around doors, panels or openings that show gaps or wear.
• Helps stop common symptoms like leaking, moisture buildup, or visible gaps at the seam.
• Keeps components aligned so doors close smoothly and seals wear evenly.

• Always disconnect power and turn off the water supply before starting any repair.
• Use hand tools to remove trim or retaining rings carefully; wear gloves to protect hands from sharp edges.
• Inspect surrounding gasket and mounting surface; replace damaged gaskets and clean mating surfaces before installing the new ring.
• After installation, test the appliance for proper seal and operation.

This bearing helps the appliance's rotating assembly turn smoothly and reduces metal-on-metal wear for quieter, more reliable operation. Replace a worn bearing to address noise and movement issues that affect performance. What it does:

• Supports the drum or tub shaft so it rotates with minimal friction
• Reduces grinding, rumbling, or squeaking noises from the rotating assembly
• Helps prevent excessive wobble or vibration during spin cycles
• Limits metal wear that can lead to leaks or further component damage

• Disconnect power and water before starting work
• Inspect surrounding seals, shafts, and mounting surfaces for wear while replacing the bearing
• Use correct tools and replacement hardware; follow OEM instructions for torque and alignment