Kenmore Dishwasher 665.1571592 (6651571592, 665 1571592) Parts

A small mounting clip that secures interior panels or trim pieces to the appliance, keeping parts aligned and preventing rattling or movement during operation. Simple replacement restores proper fit and reduces noise from loose components. What it does:

• Holds a panel, trim or small component in place on the cabinet or housing
• Keeps parts aligned so doors, panels or covers fit and operate smoothly
• Prevents rattling or vibration caused by loose or missing fasteners
• A worn or broken clip can allow gaps, movement, or noise during use

• Disconnect power (unplug or switch off breaker) before servicing
• Replacement typically requires only basic hand tools; keep track of any removed fasteners
• Inspect surrounding mounting points and adjacent clips for wear and replace as needed

Color: White. Size: 13 oz. Spray paint primer. can.

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

Restore smooth loading and secure placement for your dishes with this replacement dishrack. Replacing a bent, rusty, or damaged rack helps keep items upright, improves spray coverage, and prevents flaking or broken tines from contaminating the wash. What it does

• Holds and organizes dishes, bowls, and cookware during the wash cycle
• Slides on the rail system for easy loading and unloading
• Helps maintain proper spray coverage and drainage for effective cleaning
• Common symptoms of failure: rusted or broken tines, peeling rack coating, rack wobbling or derailing, poor rolling, items tipping over

What's included

• 1 dishrack

Install notes

• Disconnect power and shut off water; open the door and fully extend the rack
• Remove rail stop clips/end caps as applicable and slide out the old rack; wear gloves to avoid cuts from sharp edges or rust
• Transfer any reusable accessories (silverware basket, clips, holders) from the old rack if needed
• Slide the new rack onto the rails, reinstall the stops, and verify it glides smoothly before running a cycle

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

This replacement silverware basket holds forks, knives and spoons in the dishwasher lower rack so utensils stay upright and separate for better cleaning and easier unloading. It's a direct-fit interior basket designed to restore secure utensil loading. What it does:

• Keeps silverware and small utensils contained so pieces don't fall through or block the spray arms
• Separates items to improve water flow and cleaning coverage
• Prevents loose utensils from banging and potentially damaging dishes
• Replaces cracked, broken, or missing baskets that allow utensils to shift during the cycle

• Drop into the lower rack — no tools required for typical swap-out
• Position basket so it sits flat and does not interfere with rack movement or spray arm rotation
• Avoid overloading; place sharp utensils point-down or bundle separately to reduce hazard when unloading
• For appliance repairs beyond simple replacement, disconnect power and water before servicing

Includes both left and right arms.

Screw for wash impeller.

This lower spray arm assembly circulates pressurized wash water across the bottom rack to help remove food soil and improve cleaning. It replaces a worn or damaged lower arm to restore proper spray coverage. What it does:

• Directs water flow from the pump to wash dishes on the lower rack.
• Helps maintain even spray pattern and consistent cleaning performance.
• Can prevent poor cleaning or missed spots caused by cracked, clogged, or broken arms.
• Connects to the dishwasher's spray tube or hub to rotate during the wash cycle.

• Disconnect power to the dishwasher before servicing.
• Remove the lower rack to access and remove the old spray arm; typically snaps or unscrews from the hub.
• Inspect the spray arm hub and spray tube connection for debris before installing the new arm.
• Reinstall the lower rack and run a short cycle to verify proper rotation and no obstructions.

This premium dispenser cam engages the dispenser mechanism to control door/lever movement and ensure reliable dispense actions. It replaces a worn cam to restore proper dispenser function and consistent operation. What it does:

• Rotates and times the dispenser lever/door so the dispenser opens and closes correctly
• Transfers motion from the actuator to the dispenser linkage or switch
• Commonly used when the dispenser lever feels loose, doesn't return, or dispensing is intermittent
• Helps stop unwanted continuous dispensing caused by a worn cam surface

• Disconnect power (and water supply if applicable) before starting work
• Access the dispenser assembly; removal of the dispenser bezel or control housing may be required
• Handle small plastic parts carefully to avoid breaking tabs; align cam on shaft before reassembly
• Test dispenser operation after reassembly to ensure correct movement and sealing

Size: 8-32 x 1/4 inch.