Kenmore Dishwasher 665.1677993 (6651677993, 665 1677993) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369193
Color: Black. Other colors: For white use WP3369614.
Do-It-Yourself Stories from Customers like You
The access panel broke and needed to be replaced this part is located above the toe panel and just below the door Charles K. • Van , TX • February 09, 2016
I carefully removed the insulation and metallic trim from the original part using a small knife. I wraped the insulation with Glad Press'n Seal plastic wrap and attached it to the inside of the new part with double sided tape. I attached the metallic trim to the new part with super glue and then attached the Access Panel to the lower front of the dish washer. It took about 30 minutes to do the job but it was not difficult.
Read more
More
$74.95
- Compare At:
-
$88.44
- You Save:
-
$13.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3376397
Included with nut.
Do-It-Yourself Stories from Customers like You
Inadequate cleaning of dishes / detergent residue all over the interior Randy N. • Elkhart , IN • September 19, 2015
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately.
Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it...
Read more
More
$65.64
- Compare At:
-
$78.11
- You Save:
-
$12.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3374343
This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.
- Counterbalances the door for smooth opening and closing
- Helps prevent the door from slamming open or feeling heavy
- Supports stable, mid-position hold when springs are intact and matched
- Common signs of failure: door drops quickly, is hard to lift, or won't stay in position
What's included: 1 door spring Installation notes:
- Disconnect power and water; remove the toe kick/access panel to reach the springs
- Note which frame/hinge holes the old spring used and install the new spring in the same positions to match tension
- Use pliers to relieve tension safely; if your model uses two springs, replace both for balanced operation
- Wear gloves and eye protection; keep hands clear of moving hinges
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$21.95
- Compare At:
-
$26.34
- You Save:
-
$4.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302710
This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.
- Forms a tight, continuous seal at the inlet base-to-housing joint
- Helps preserve correct airflow through the inlet path
- Blocks liquids, grease, and crumbs from leaking into the appliance interior
- Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps
What's included: One inlet base seal.
- Disconnect power to the appliance before servicing
- Remove grates/cartridges, filters, or trim as needed to access the inlet base
- Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
- Reassemble and verify the seal sits evenly with no gaps
Do-It-Yourself Stories from Customers like You
Leaks from around the door and from the pump motor Samuel M. • Sudbury , MA • January 12, 2016
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed...
Read more
More
$6.63
- Compare At:
-
$7.89
- You Save:
-
$1.26
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369000
This upper draw bar is a door-latch linkage piece used in dishwashers. It connects the handle/actuator to the latch mechanism so the door closes securely and the door switch engages, allowing the cycle to start reliably.
- Links the door handle/actuator to the latch for positive closure
- Helps ensure the door switch is engaged so the unit will run
- Restores proper latch alignment and handle feel
- Common symptoms: door won't latch or pops open, dishwasher won't start, must push/hold door to run, loose or floppy handle
What's included: 1 upper draw bar Installation notes:
- Disconnect power at the breaker; turn off water supply if working near the inlet
- Open the door and remove inner-door screws to access the latch linkage
- Note bar orientation; transfer any clips/bushings and reuse existing hardware
- Reassemble and check latch engagement before running a cycle
Do-It-Yourself Stories from Customers like You
Latch would not open consistently on detergent dispenser James G. • Waxhaw , NC • January 12, 2015
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3374077
Size: 7 foot long.
Do-It-Yourself Stories from Customers like You
Bought a used dishwasher in excellent shape that needed the drain pieces to get it going Johnny R. • San Antonio , TX • April 14, 2015
Bought the parts and connected same...a breeze in finding and receiving and eventually installing these parts.
Read more
More
$62.78
- Compare At:
-
$74.71
- You Save:
-
$11.93
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: 8193716
This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.
- Provides adjustable support at one corner of the appliance
- Helps level the unit for correct alignment with floor or cabinetry
- Reduces rocking, vibration, and rattling noises
- Replaces stripped, bent, cracked, or missing leg
What's included: 1 adjustable leveling leg Install notes:
- Disconnect power and, if applicable, shut off water before servicing
- Carefully support or brace the appliance to access the base safely
- Start the new leg by hand to avoid cross-threading; adjust height gradually
- Use a level to check side-to-side and front-to-back, then recheck after positioning
More
$43.95
- Compare At:
-
$52.30
- You Save:
-
$8.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3371710
This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.
- Screens the door vent to keep debris out of the vent duct and fan path
- Maintains airflow for venting steam during the dry cycle
- A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
- Replace if warped, broken, or lost during service
What's included: 1 vent screen Install notes:
- Disconnect power to the dishwasher at the breaker before servicing
- Open the door and remove inner-door screws to access the vent assembly
- Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
- Run a short cycle and check the vent area for proper airflow and moisture
Also known as: Screen, Vent
Do-It-Yourself Stories from Customers like You
Water splashing out of the vent on the front of the door as well as dripping on the floor from the bottom of the door Joe K. • Gypsum , CO • November 09, 2014
This screen simply snaps into place. The repair took less than 1 minute.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489128
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: 285006
Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.
Do-It-Yourself Stories from Customers like You
My 1984 dishwasher that still works great was an eyesore & I didn't match my other appliances. Dorothy L. • Raleigh , NC • March 24, 2014
I purchased a can of black appliance spray paint, removed the panels on the dishwasher, sprayed them, and a few hours later put them back. They're beautiful and it looks like I have a brand new dishwasher! It now matches everything and looks great with the new granite counter tops I just installed. THANK YOU FOR THE GREAT IDEA!!! I'm a 76 year old female and my friends think I'm a genius!
Read more
More
$42.95
- Compare At:
-
$51.11
- You Save:
-
$8.16
Genuine Whirlpool part
By: Whirlpool
Part Number: WP304231
Size: 8-18 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
My whirlpool gas dryer wouldn't start was stuck in the "sensing" stage Kirill D. • Livingston , NJ • January 05, 2015
After I disassembled the dryer, I discovered that the belt was broken. Using a very handy video from the site I raced the belt and everything is back to normal
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13