Kenmore Range 665.75022101 (66575022101, 665 75022101) Parts

This genuine control knob provides a simple, tactile replacement for a damaged, worn, or missing appliance control. Restores a secure grip and precise control so settings are easy to read and adjust. What it does:

• Replaces a cracked, loose, stripped, or missing control knob so you can safely change settings
• Fits over the appliance control shaft and provides a clear pointer for accurate selection
• Restores tactile feedback for smooth turning and reliable position stops
• Helps prevent accidental setting changes from slipping or worn grips

• Disconnect power to the appliance before installing to avoid injury
• Pull off the old knob straight from the control shaft; align splines and push the new knob on until fully seated
• If the old knob is stuck, use a gentle, even pulling force or a plastic knob puller to avoid damaging the control shaft

This hinge pin fits hinged-top ranges and provides the pivot point for the cooktop. Replacing a worn or missing pin helps restore smooth lift action, alignment, and stability when opening the top for cleaning or service.

• Provides the pivot between the cooktop and hinge bracket for lift-up operation
• Helps keep the cooktop aligned and stable when closed
• Common symptoms include a loose or wobbly cooktop, scraping or binding when lifting, or uneven gaps
• Replacing a damaged pin helps restore smooth, secure movement

• Disconnect power and turn off gas supply before servicing
• Support the cooktop to prevent strain on the hinges while working
• Remove the old pin and any retainer; install the new pin in the same orientation and fully seat it
• Verify smooth, aligned operation before restoring power and gas

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

A self-tapping screw used to secure appliance panels and components, providing reliable fastening to sheet metal and plastic parts. Replaces worn or missing fasteners to restore proper fit and reduce rattling. What it does:

• Fastens panels, brackets, or trim to appliance frames and housings
• Creates its own threads in sheet metal or plastic for a secure hold
• Helps stop loose panels, vibration noise, and misaligned parts
• Commonly used where a short, durable fastener is needed

• Disconnect power and water before starting any repair
• Use the correct screwdriver or driver bit to avoid stripped heads
• Start threads carefully and avoid over-torquing to prevent damage
• Wear eye protection and gloves when working with sheet metal

This rail base provides the structural support for the refrigerator drawer/rail assembly, restoring smooth drawer alignment and preventing sagging or binding. It's a direct-fit replacement that helps maintain proper drawer operation and cabinet fit. What it does:

• Supports and aligns the drawer/rail assembly so drawers slide smoothly
• Secures the lower rail to the cabinet to prevent shifting or sagging
• Restores proper drawer clearance and prevents sticking or uneven movement
• Addresses symptoms like crooked or loose drawers, binding, or gaps at the drawer edge

• One rail base

• Disconnect power to the appliance before beginning work
• Remove drawer(s) and any trim panels to access the rail area
• Use basic hand tools; avoid overtightening fasteners to prevent damage

Color: White. Size: 13 oz. Spray paint primer. can.

This is a genuine replacement screw used to secure appliance components. It provides a simple, reliable fastener for reattaching panels, brackets, or assemblies so parts stay properly mounted and stable during operation. What it does

• Secures panels, trim, brackets or small assemblies in place
• Restores proper fastening where a missing or damaged screw causes loose parts or rattling
• Prevents movement that can lead to noise or misalignment of adjacent components
• Used wherever the original screw was removed or lost during repairs

• One replacement screw

• Use the matching screw head and thread engagement; do not force if it does not seat smoothly
• Tighten until snug—avoid overtightening to prevent stripping or cracking plastic parts
• Disconnect power before working on electrical appliances and follow basic safety precautions
• If original screw was rusted, check mating threads for damage before installing new fastener

This spud orifice controls the gas flow to a burner, ensuring proper flame size and consistent cooking or baking performance. It replaces a worn or damaged natural-gas orifice to restore safe, reliable burner operation. What it does:

• Meter gas to the burner for correct flame height and even heat
• Helps prevent weak flames, uneven cooking, or ignition issues
• Restores proper combustion when the original orifice is clogged or damaged
• Works with the burner tube and manifold to maintain oven/range performance

• Only install with the appliance disconnected from gas and power; follow local codes
• Use correct torque and fittings; check for leaks with a soap solution or approved leak detector
• Replace only with the same or manufacturer-approved orifice size for safe operation

Color: White. Size: 8-18 x 3/8 inch.

This replacement screw secures appliance panels and components to keep parts aligned and stable. Use it to replace missing or damaged fasteners that cause loose trim, rattling, or unsecured panels for safer, quieter operation. What it does:

• Fastens panels, brackets, trim pieces, or small components in place
• Restores proper alignment and stops vibration or rattling caused by loose hardware
• Replaces stripped, corroded, or missing screws to prevent parts from shifting or falling
• Compatible where the OEM lists part W11244557 as the required fastener

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid over-tightening, which can strip threads or crack parts
• Replace like-for-like; length before installing

This replacement door light switch controls the oven interior light so it turns on and off with the door, restoring expected visibility when checking food or performing maintenance. Ideal for ovens with a pyrolytic/self-clean cycle. What it does:

• Opens and closes the circuit to the oven interior light when the door is opened or closed
• Stops the light from staying on or not turning on when the door is operated
• Helps restore normal oven-light operation after a failed or worn switch
• Matches OEM function and mounting for direct-fit replacement on compatible pyro ovens

• Disconnect power to the appliance before starting any repair
• Access may require removing the oven door or inner door panel—handle glass panels carefully
• Verify correct switch position and wiring before reassembly; test operation after restoring power

This broiler burner provides the gas flame for the oven's broil function, restoring high-heat cooking performance for searing and browning. Designed for direct-spark-ignition (DSI) ranges, it replaces a worn or damaged broil element. What it does:

• Produces the high, direct flame used for broiling food on the oven's top rack
• Replaces a cracked, rusted, or clogged burner that causes uneven or weak broiling
• Stops burner-related ignition issues when the burner tube or ports are damaged
• Helps restore proper heat distribution for faster browning and searing

• One broiler burner

• Disconnect electrical power and shut off the gas supply before starting work
• Handle gas connections and igniter areas carefully; inspect for leaks after installation
• Use basic hand tools; ensure the burner seats and aligns with the gas orifice and igniter

This burner baffle sits under the cooktop burner to direct heat and protect surrounding components, helping maintain even flame distribution and preventing debris from falling into the burner area. What it does:

• Shields the area under the burner from spills, grease and food debris.
• Helps route heat and combustion gases away from sensitive components.
• Supports stable burner operation and consistent heating performance.
• Commonly replaced when warped, corroded or damaged by spills.

• Turn off gas and power to the appliance before servicing; follow all safety precautions.
• Remove burner grates and caps to access the baffle; use basic hand tools.
• Inspect surrounding components (burner head, igniter) while the baffle is removed.

This spud orifice regulates the flow of natural gas to a burner, helping maintain the correct flame size for safe, efficient cooking. It replaces worn or damaged orifices to restore reliable ignition and burner performance. What it does:

• Meters natural gas to the burner to produce the proper flame for cooking
• Helps maintain consistent heat output and stable ignition
• Commonly replaced when flames are weak, uneven, yellow-tipped, or the burner won't light reliably
• Compatible with factory burner assemblies that use a spud-style orifice

• Turn off gas supply and unplug the appliance before servicing
• Use appropriate tools; avoid overtightening the orifice when installing
• After installation, check for gas leaks and proper burner operation before regular use