Kenmore Range 790.46359400 (79046359400, 790 46359400) Parts

This backguard kit replaces the upper rear panel and trim on compatible ranges to restore a clean appearance and protect wall and controls from spills and heat. It's a direct-fit exterior repair for damaged, bent, or corroded backguards. What it does:

• Replaces the upper rear backguard panel and trim to restore the range's finished rear appearance
• Protects the control area and wall from splashes, grease, and heat exposure
• Helps stop drafts and gaps behind the range that can collect debris
• Addresses visible damage like dents, rust, or cracked trim

• Disconnect power to the range (unplug or switch off breaker) before starting work.
• Installation may require lifting and aligning the panel; use a second person for safety on larger ranges.
• Use common hand tools; keep fasteners and mounting brackets from the old assembly if reusable.
• Follow the appliance manufacturer's service instructions for model-specific steps and torque values.

Secures the heating element to the cooktop surface. Replace if your original spring is broken, missing, or no longer holds the element firmly in place.

Color: chrome. Measures about 23 inches wide by 15 inches deep.

This is a replacement refrigerator door gasket that restores the seal around the door to help maintain proper temperature and efficiency. It's a direct-fit sealing strip designed to replace a worn, torn, or deformed door seal. What it does:

• Seals the gap between the door and cabinet to help keep cold air in and warm air out
• Helps reduce frost buildup and prevents moisture and leaks around the door
• Restores consistent internal temperature for better food preservation
• Reduces compressor run time caused by an improper door seal

• One refrigerator door gasket

• Recommended: replace gasket on a clean, dry door surface; remove old gasket and adhesive residue before installing
• Use the manufacturer's recommended attachment method (snap-in or adhesive) for your model
• Inspect hinge alignment and door fit before finalizing gasket installation to ensure an even seal
• For safety, unplug the appliance or disconnect power before beginning repairs

Secures cooktop surface elements to your range for stable contact and even heating. Replace if bent or worn to restore proper element positioning.

This replacement refrigerator door handle restores a secure, easy-to-grip pull for opening and closing the fridge. It matches the original mounting points for a clean, factory-fit appearance. What it does

• Replaces a cracked, loose, or broken refrigerator door handle so the door can be opened and closed safely.
• Provides a solid grip to help prevent slips and accidental drops.
• Restores proper clearance and alignment at the door edge for smooth operation.
• Helps maintain the appliance's original look and usability.

• One replacement refrigerator door handle.

• Installation requires removing the old handle and fastening the new handle to the existing mounting points; keep mounting screws and any trim pieces from the original assembly.
• Use basic hand tools; avoid over-tightening fasteners to prevent cracking the handle.
• Disconnect power only if instructed by the appliance manual for your specific model (most handle replacements do not require powering down).
• If the handle attaches under a trim or gasket, take care to reseat trim evenly to maintain door seal integrity.

Replacement control panel for your oven. Installs on the front to house controls and display. Order a new panel if yours is cracked, damaged, or discolored.

Rear filler kit assembly that installs behind slide-in ranges to close the gap between the range and wall. Replace if missing, cracked, or damaged.

Mounting spring that secures the heating element in place on your cooktop. Replace if spring is broken, stretched, or missing to properly hold element.

Insulation panel for ovens and ranges. Installs inside the oven cavity to provide heat retention and sound dampening. Replace if torn, compressed, or missing.

Rubber or plastic bushing that cushions and supports the oven door. Replace if cracked, worn, missing, or causing door misalignment or rattling.

Insulates and cushions the oven cabinet interior. Replace if cracked, damaged, or missing to restore thermal separation and reduce condensation.

Anti-tip warning label for electric ranges. Replaces faded, peeling, or missing safety labels on the anti-tip bracket. Ensures compliance with safety standards.

This spacer positions and separates mounting components to maintain proper clearance and alignment, helping panels and hardware fit securely. It prevents rubbing and keeps assemblies stable for quieter, correct operation. What it does:

• Maintains required gap between panels or mounting surfaces to prevent binding or interference
• Keeps screws, brackets, and panels aligned for a proper fit
• Reduces vibration and rattling caused by loose or misaligned parts
• Helps restore proper clearance when replacing worn or missing spacers

• Disconnect power before accessing internal panels or fasteners
• Replace like-for-like; spacer location and orientation during removal
• Handle surrounding trim and panels carefully to avoid damage
• If fasteners are damaged or stripped, replace them rather than over-tightening