Kenmore Range 790.71313708 (79071313708, 790 71313708) Parts

Supports and controls oven door movement on gas and electric ranges. Replace if hinge is broken, cracked, or spring mechanism has failed causing door sag.

This is a gas valve that controls the flow of gas to a surface burner on a gas range. It connects to the burner control knob and regulates the flame from high to low settings. Replace this valve if a burner won't ignite, the flame is uneven or won't adjust properly, or you detect a gas smell when the knob is in the off position. Includes mounting screw.

This is a replacement refrigerant/line connection tube that links the service valve to the regulator line, restoring a sealed pathway for proper cooling system operation. It fits systems using a 3/8" tube connection. What it does:

• Connects the service/stop valve to the regulator/line, maintaining a sealed refrigerant path
• Restores proper flow and pressure routing when the original tube is damaged, cracked, or leaking
• Commonly replaced for visible leaks, hissing at the valve area, or loss of cooling tied to a line break
• Works as a direct, single-piece tubing connector where a 3/8" connection is specified

• One tube to valve connector (3/8" tube)

• Installation requires appliance access and basic refrigeration line handling; tighten fittings to OEM torque specs and verify leak-free with an appropriate leak detector
• Wear safety glasses and gloves; avoid breathing refrigerant vapors and follow manufacturer service documentation

This broil pan insert fits inside your oven's broiler pan to allow grease and fat to drain away from food while broiling. The slotted design promotes even cooking and prevents food from sitting in grease. Replace this insert if it's warped, has holes burned through it, or is heavily stained and won't clean properly.

This is a metal broiler pan designed to sit beneath the broil element in the oven or broiler compartment. It catches grease and drippings during broiling to reduce smoke and prevent grease fires. Replace this pan if it is warped, corroded, or has holes that allow grease to leak through.

This is a black metal side panel that attaches to the left exterior side of the range, providing a finished appearance and structural support. It helps enclose and protect the internal components of the oven cavity. Replace this panel if it is dented, rusted, scratched, or damaged from heat exposure.

Wafer-head screw with square drive secures range trim, handles, and panels. Replace when missing, stripped, or corroded to keep components firmly attached.

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

Secures gas valve assemblies and mounting brackets to your range. Replace if screw is stripped, missing, or corroded to keep valve hardware stable.

Support plate that mounts to the bottom of your range oven cavity. Replace if the original plate is cracked, warped, or damaged from heat exposure.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This is the right-side outer panel for a freestanding range, providing the exterior surface that faces outward when the unit is installed at the end of a counter run. It gives the range a finished appearance and protects internal components. Replace this panel if it is dented, scratched, rusted, or otherwise damaged.

Mounting bracket for gas ranges. Secures components inside your range. Replace if bent, broken, or missing to restore proper structural support.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.