Kenmore Range 790.73054401 (79073054401, 790 73054401) Parts

This replacement clip secures components within your appliance. Replacing a broken, bent, or missing clip restores a firm hold on panels or assemblies to prevent shifting and reduce vibration noise.

• Holds specified parts or panels in place where a clip is called out in the assembly
• Helps maintain proper alignment and minimizes rattles/vibration
• Direct replacement for a damaged or missing clip
• Common symptoms: loose or misaligned parts, rattling during operation, clip visibly broken or missing

• Disconnect power before service; also shut off gas/water supplies
• Note the original clip orientation and placement; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid overbending or deforming the clip
• Inspect mating parts for wear or damage and ensure the clip seats fully

Color: Black.

Size: 6-20 x 0.312 inch.

A small replacement retainer clip that secures trim, panels or components in place to restore proper alignment and stop rattles or loosening. Fits original mounting points for a factory-style repair. What it does:

• Secures refrigerator trim, panels or small components to prevent movement and noise
• Keeps parts aligned so doors and drawers fit and operate smoothly
• Helps maintain grille, kickplate or interior trim attachment where clips are used
• Simple, non-electrical part — no wiring or calibration required

• Basic hand tools usually required; access the clip location before removal
• Remove any panels gently to avoid damaging surrounding trim or fasteners
• Replace only the worn or broken clip; align part fully before snapping into place
• Disconnect power to appliances with electrical components before starting work

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

This valve mounting screw secures refrigerator water/ice valve assemblies and their mounting brackets, helping keep the valve stable and properly aligned. A simple replacement to address loose or vibrating valve hardware. What it does:

• Secures the valve mounting bracket to the appliance cabinet or valve body
• Fits standard 1/4-20 threaded valve mounting points
• Restores secure mounting when original screw is loose, missing, or stripped
• Helps reduce vibration-related noise and the risk of valve movement that can lead to leaks

• Disconnect power and shut off the water supply before servicing
• Start the screw by hand to avoid cross-threading, then tighten until snug
• Do not over-tighten; replace if threads are stripped or damaged

The Pressure Regulator is an OEM part for Frigidaire gas ranges. It controls incoming gas flow to the burner valves and maintains consistent heat levels.

Causes of a bad pressure regulator can include cracks or leaks developing in the seal over time, clogs or debris buildup affecting flow control, or damage to pressure monitoring components.

Symptoms of a bad pressure regulator include:

• Fluctuating burner flames and heat output
• Inability to stabilize gas pressure for predictable cooking
• Yellow or sooty flames indicating inefficient combustion
• Safety risk of gas leaks at increased pressures

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This flue directs exhaust and heat away from the oven cavity to the range vent path, helping maintain proper ventilation and combustion airflow. It replaces damaged or corroded flue components to restore safe venting and oven performance. What it does:

• Channels heat, smoke and combustion exhaust from the oven cavity toward the vent path
• Helps prevent heat buildup behind the oven control area and adjacent panels
• Can reduce visible soot, odors or poor venting caused by a cracked or bent flue
• Supports proper burner combustion airflow in gas models when correctly installed

• One replacement flue

• Disconnect the appliance from power (and gas supply on gas models) before starting work
• Access typically requires removing the oven back panel or drop-in cooktop; keep track of mounting screws and gaskets
• Wear gloves to protect from sharp sheet-metal edges and use caution aligning the flue to vent openings
• After installation, restore power/gas and verify normal oven operation and proper venting; check for signs of leaks or loose fasteners

0.6 fluid ounces

Note: ONE screw only, order as needed.