Kenmore Range 790.78409010 (79078409010, 790 78409010) Parts

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This cabinet insulation helps reduce heat transfer inside the refrigerator, supporting stable temperatures and efficient cooling. Replacing damaged or missing insulation can improve temperature control and reduce frost buildup. What it does:

• Fills gaps between the cabinet and liner to slow heat transfer and maintain internal cold
• Helps the appliance reach and hold set temperatures more consistently
• Reduces condensation and excess frost on interior surfaces
• Can improve compressor run-time and overall energy efficiency when intact

• Disconnect power before starting
• Remove food and shelving from the compartment before accessing the insulation
• Handle insulation carefully to avoid tearing; secure per manufacturer routing and adhesive points
• Dispose of old insulation per local regulations

This orifice is the small gas jet that meters fuel to a range or oven burner, helping restore correct flame size and consistent heat for reliable cooking performance. What it does:

• Controls the gas flow to a burner, producing the correct flame for even heating
• Commonly used when flame is unusually small, weak, or uneven
• Helps address burners that light slowly or do not reach proper temperature
• Works as part of the burner assembly with the regulator and valve to maintain safe operation

• One orifice

• Turn off gas supply and electrical power before starting work
• Do not force threads; use appropriate thread sealant if specified by OEM
• After installation, check all fittings for leaks with a gas-safe detector or soapy water

This genuine oven bake element heats the oven cavity for baking and roasting, restoring proper cooking temperatures and consistent results. Replaces a damaged or non-heating bake element to bring your oven back to service. What it does:

• Heats the oven cavity so food reaches and holds set temperatures
• Restores even baking and roasting when the oven fails to heat
• Replaces elements that show visible damage, burn-through, or no glow
• Works with electric ovens that use a separate bake heating element

• Disconnect power to the appliance at the breaker before starting work
• Handle the element carefully to avoid bending or damaging terminals
• Remove oven racks and access the element from inside the oven
• Verify proper fit and secure mounting; tighten terminal fasteners firmly and restore power to test

This inner oven door glass replaces a cracked, broken or fogged inner door panel to restore thermal performance and visibility into the oven cavity. It helps keep heat in the oven and prevents direct exposure to the internal cavity. What it does:

• Replaces damaged or cracked inner oven door glass that can compromise heating and safety
• Restores the oven door's insulating layer to reduce heat loss and improve cooking consistency
• Provides a clear viewing window to check food without opening the door
• Stops rattling or vibration caused by loose or broken glass

• Disconnect power to the appliance and ensure the oven is completely cool before starting
• Wear cut-resistant gloves and eye protection when handling glass to avoid injury
• Some installations require removing the oven door and disassembling door screws or clips; keep fasteners organized

This wire rack provides a sturdy, corrosion-resistant shelf surface to support food containers, pans and other items inside the compartment. It restores usable storage space and helps keep items organized and level. What it does

• Replaces a bent, broken or missing wire shelf so items sit flat and don't slide or tip
• Supports dishes, trays and food containers for safe storage and even airflow
• Maintains proper spacing for drawers and other interior components to operate
• Visible wear or rust on the wires can cause sharp edges or instability

• High-level swap: remove any items, lift out the old rack and set the new rack into the existing support grooves or clips
• No special tools typically required; gentle pressure may be needed to seat rack into supports
• If rack has mounting clips, confirm clips are intact and positioned correctly before use
• For safety, avoid forcing parts;

This thermo disc is a small temperature-sensing switch that helps monitor and control appliance temperatures to protect components and support proper operation. It fits into the appliance's temperature circuit and responds at a designed trip point. What it does

• Senses temperature and opens or closes an electrical circuit at its rated trip point
• Helps prevent overheating by interrupting power when temperatures exceed the design threshold
• Supports proper temperature control for timed cycles or safety systems
• Commonly used in temperature-regulation and safety applications inside appliances

• One thermo disc

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Replace only with the exact part number for proper function and safety
• Handle the disc carefully; avoid bending or damaging the sensing element or terminals