Kenmore Range 790.78629400 (79078629400, 790 78629400) Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This control panel is the exterior trim that houses and protects the oven/range user interface and display, restoring a clean, functional front for the appliance. It keeps buttons and indicators secure and visible for reliable operation. What it does:

• Covers and protects the appliance control buttons, touchpad, and display from spills and damage
• Provides the visible interface for selecting oven functions and viewing status
• Restores a finished appearance to a damaged, cracked, or worn control area
• Helps ensure buttons and indicators align properly for correct operation

• One control panel

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Some models require removing screws or snap clips and gently lifting the old panel from the console
• Handle the panel carefully to avoid scratching the visible finish or bending mounting tabs
• If the panel attaches to electronic components, take care not to damage ribbon cables or connectors; take care not to damage ribbon cables or connectors.

A small replacement retainer clip that secures trim, panels or components in place to restore proper alignment and stop rattles or loosening. Fits original mounting points for a factory-style repair. What it does:

• Secures refrigerator trim, panels or small components to prevent movement and noise
• Keeps parts aligned so doors and drawers fit and operate smoothly
• Helps maintain grille, kickplate or interior trim attachment where clips are used
• Simple, non-electrical part — no wiring or calibration required

• Basic hand tools usually required; access the clip location before removal
• Remove any panels gently to avoid damaging surrounding trim or fasteners
• Replace only the worn or broken clip; align part fully before snapping into place
• Disconnect power to appliances with electrical components before starting work

A replacement protective shield that covers and protects internal appliance components from debris, moisture and incidental contact. Restores protection to damaged or missing shields to help maintain safe, reliable operation. What it does:

• Covers and protects wiring, connectors or nearby parts from accidental contact and debris
• Helps prevent moisture or food particles from reaching sensitive components
• Replace if the shield is cracked, warped, missing or allows exposed parts
• Reduce rattles or contact-related noises caused by loose or damaged shields

• Shield

• Disconnect power to the appliance before starting any repair
• Use care around sharp edges; wear gloves and eye protection
• Remove fasteners holding the old shield; reuse or replace screws as specified by the manufacturer

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fastening to reduce vibration and keep parts aligned for safe, reliable operation. What it does:

• Secures panels, brackets, and trim to prevent rattling or loosening
• Restores proper fit where a damaged or missing screw caused gaps or movement
• Helps maintain component alignment for smooth operation
• Simple hardware replacement that supports overall appliance stability

• Disconnect power and gas before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or part damage
• Keep small parts away from children and dispose of old fasteners responsibly

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

This valve mounting screw secures refrigerator water/ice valve assemblies and their mounting brackets, helping keep the valve stable and properly aligned. A simple replacement to address loose or vibrating valve hardware. What it does:

• Secures the valve mounting bracket to the appliance cabinet or valve body
• Fits standard 1/4-20 threaded valve mounting points
• Restores secure mounting when original screw is loose, missing, or stripped
• Helps reduce vibration-related noise and the risk of valve movement that can lead to leaks

• Disconnect power and shut off the water supply before servicing
• Start the screw by hand to avoid cross-threading, then tighten until snug
• Do not over-tighten; replace if threads are stripped or damaged

The Lens is an OEM component for Frigidaire freezers. It acts as a transparent cover and protective barrier for the freezer compartment lights. Crafted for durability and clarity, the lens avoids frost and minimizes condensation while allowing visibility inside the freezer.

Causes of a bad lens can include deep scratches or cracks developing over time from repeated wiping or exposure to chemicals like frost removers.

Symptoms of a bad freezer lens include:

• Cloudiness, fogginess, or smears inhibiting internal visibility
• Cracks or breaks compromising the protective barrier
• Distorted views make it difficult to assess food levels
• Diffused lighting with shadows instead of a clear view

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Door Lock Motor and Switch Assembly is an OEM component specifically designed for Frigidaire ranges. This locking system safely secures oven doors during cleaning or self-clean cycles through the electromagnetic operation. 

Symptoms of a defective assembly include: 

• Failure to engage or release the door lock function
• Loud buzzing or grinding noises from internal mechanisms  
• Error codes related to door lock detection problems

Causes relate to wear from continual operation of locking solenoids over extended use. Exposure to cooking residues and cleaning chemicals can deteriorate switches. 

This OEM Frigidaire part is also compatible with some Kenmore and GE appliance brands. Replacing worn components restores reliable door locking to automatically secure during high-heat cycles. Timely maintenance preserves safety functionality.
 

This replacement refrigerator cabinet liner restores the appliance's interior surface, helping contain spills and support shelves/drawers for reliable storage. Fits specific Frigidaire models; use the part number on your unit. What it does:

• Replaces cracked, warped or damaged interior surface that can allow moisture, odors, and debris to collect
• Provides the finished interior surface that supports shelf and bin mounting points
• Helps maintain a clean, easy-to-wipe interior and prevents insulation exposure
• Reduces the risk of leaks by restoring the proper fit and seals where the liner meets doors and gaskets

• One refrigerator cabinet liner as shown

• Disconnect power and empty the refrigerator before starting; follow manufacturer safety guidance
• Installation generally requires removing shelves, drawers and trim; small fasteners or clips may secure the liner
• Avoid sharp tools to prevent damage; inspect surrounding seals and hardware while replacing the liner