Kenmore Range 790.90214012 (79090214012, 790 90214012) Parts

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This door trim kit replaces the perimeter trim on the appliance door to restore a clean, factory finish. It covers and protects the door edges when the original trim is cracked, warped, or missing.

• Frames the door perimeter for a finished, uniform appearance
• Helps cover raw edges to prevent snags and rattling
• Replaces cracked, warped, or missing trim pieces
• Common signs include loose or missing trim, cosmetic damage, and gaps along the door edge

• Disconnect power (and gas, if applicable) and allow the appliance to cool before service
• Support the door; remove it if your service information recommends
• Carefully remove old trim; handle glass and sharp edges with cut-resistant gloves
• Align and secure the new trim; avoid overtightening fasteners and verify smooth door operation

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This control panel is the front console assembly that houses the user controls and display, restoring proper button access and visible status indicators so you can select cycles and monitor operation. What it does:

• Provides the tactile buttons and display area for user input and cycle selection
• Protects and aligns the underlying electronic controls and switches
• Restores readable status lights and labels that indicate selected settings
• Commonly replaced when buttons are unresponsive, cracked, or cosmetic damage prevents normal use

• One control panel/console assembly

• Verify power is disconnected before starting any repair to avoid shock or damage
• Replacement typically requires removing the outer cabinet or control trim; keep hardware organized
• Inspect underlying switches and wiring during installation; replace any damaged fasteners or clips
• Recheck connector seating and wiring harness integrity after installation

Size: 8-18ab x 0.5 inch.

This insulator is a molded protective cushion that reduces vibration and protects nearby components from wear or contact. It helps keep parts stable and minimizes noise for smoother appliance operation. What it does:

• Cushions components to reduce vibration and rattling
• Protects wiring, tubing, and panels from abrasion and impact
• Helps maintain proper spacing between parts to prevent rubbing
• Can reduce operational noise caused by loose or contacting parts

• One insulator

• Disconnect power to the appliance before starting any repair
• Remove the access panel(s) needed to reach the mounting area; retain fasteners
• Press or slide the insulator into the correct position; it fits snugly and secures the component
• If removal requires cutting old adhesive or clips, replace with equivalent fasteners or adhesives approved by the manufacturer

This bodyside bracket secures the cabinet/body components to the refrigerator frame, helping keep panels aligned and stable for smooth door operation and consistent sealing. Durable replacement for worn or damaged mounting hardware. What it does:

• Provides a stable mounting point between the cabinet side and internal frame to maintain panel alignment
• Helps prevent cabinet movement that can cause door misalignment or uneven gaps
• Restores proper support after impact, corrosion, or stripped fastener holes
• Compatible with common service repairs where the original bracket is bent or broken

• Designed for use with manufacturer-specified fasteners; reuse or replace screws as needed
• Remove power and empty nearby shelves before working to avoid injury or damage
• Use basic hand tools; avoid overtightening fasteners which can crack plastic or deform panels