Kenmore Range 790.90810402 (79090810402, 790 90810402) Parts

This support plate secures internal components and provides a stable mounting surface to reduce vibration and keep parts aligned. It restores proper fit and helps stop rubbing, rattling, or loose-panel symptoms. What it does

• Provides a flat, stable mounting surface for adjacent components
• Holds parts in correct position to prevent movement and noise
• Helps maintain proper clearances so panels and assemblies fit without rubbing
• Can be replaced if bent, cracked, or missing fasteners that cause vibration or loose parts

• Disconnect power before servicing to avoid shock or injury
• Verify plate orientation and fastener locations before removing old part
• Use existing screws if undamaged; replace damaged fasteners for secure fit
• Handle edges carefully; wear gloves to avoid cuts during install

A decorative medallion trim piece that restores the finished look of your appliance front. Replaces a scratched, faded or missing medallion to improve appearance and maintain original styling. What it does:

• Covers and protects the underlying surface while matching the appliance's original finish
• Restores a clean, finished look when the factory medallion is damaged or discolored
• Helps keep grime and moisture out of seams around the emblem area
• Useful when replacing a damaged control/door trim for a consistent appearance

• One medallion decorative trim

• Surface-mount replacement; peel adhesive or fasten per original attachment method
• Clean and dry mounting area before installing for best adhesion
• Handle carefully to avoid scratching the finish during installation

Original Frigidaire Part.

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

0.6 fluid ounces

This oven back insulation panel fits behind the oven cavity to help contain heat and protect rear components. It replaces missing or damaged insulation to help restore normal oven heating behavior and reduce heat transfer to surrounding areas. What it does:

• Limits heat loss from the rear of the oven cavity to help maintain cooking temperature
• Helps reduce excessive heat transfer to rear components and cabinetry
• Use when insulation is torn, compressed, burned, or when the oven takes noticeably longer to preheat
• Helps prevent heat-related damage to wiring, electronics, and nearby parts

• Disconnect power to the appliance before starting any repair
• Access may require pulling the range/oven away from the wall and removing a rear access panel
• Wear gloves and a dust mask when handling old insulation; avoid compressing or tearing the replacement
• Follow OEM instructions for securing insulation with the original clips/adhesive or fasteners

This replacement refrigerator door handle restores a secure, easy-to-grip pull for opening and closing the fridge. It matches the original mounting points for a clean, factory-fit appearance. What it does

• Replaces a cracked, loose, or broken refrigerator door handle so the door can be opened and closed safely.
• Provides a solid grip to help prevent slips and accidental drops.
• Restores proper clearance and alignment at the door edge for smooth operation.
• Helps maintain the appliance's original look and usability.

• One replacement refrigerator door handle.

• Installation requires removing the old handle and fastening the new handle to the existing mounting points; keep mounting screws and any trim pieces from the original assembly.
• Use basic hand tools; avoid over-tightening fasteners to prevent cracking the handle.
• Disconnect power only if instructed by the appliance manual for your specific model (most handle replacements do not require powering down).
• If the handle attaches under a trim or gasket, take care to reseat trim evenly to maintain door seal integrity.

A replacement outer glass door panel kit that restores the refrigerator door's appearance and insulating surface. The white outer panel includes foil tape for sealing and finishing the edge for a clean, factory look. What it does

• Replaces a cracked, chipped, or discolored outer glass door panel to improve appearance.
• Restores the door's exterior surface and helps maintain the door edge seal when used with the included foil tape.
• Helps prevent drafts and moisture intrusion at the door edge when installed correctly.
• Matches the original white finish for a factory-style look.

• Disconnect power to the appliance before starting and remove contents from the door.
• Handle the glass panel carefully; wear gloves and eye protection to reduce cut risk.
• Installation typically requires removing the door trim/retainer and carefully replacing the outer glass; keep fasteners and seals organized.

This chassis support is a replacement mounting bracket that helps secure the appliance cabinet and internal components for proper alignment and stability. It restores structural support to reduce movement and rattling. What it does:

• Secures the appliance chassis or cabinet to maintain correct alignment
• Stabilizes internal components to reduce vibration and noise
• Helps prevent gaps, sagging trim, or misaligned panels
• Supports proper door and drawer operation by keeping the frame square

• One chassis support mounting bracket

• Disconnect power (and water if applicable) before starting any repair
• Use basic hand tools; fasteners may need basic-sized screwdrivers or nut drivers
• Wear gloves to protect hands from sharp sheet-metal edges