Kenmore Range 790.94213402 (79094213402, 790 94213402) Parts

This replacement shield is a molded protective mounting shield that helps protect internal appliance components from debris and physical damage, keeping parts aligned for reliable operation and quieter performance. What it does:

• Covers and protects wiring, harnesses, or small components from contact and debris
• Helps maintain proper alignment of nearby parts to reduce wear and noise
• Prevents incidental interference between moving parts
• Restores intended component protection after damage or removal

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Handle plastic tabs and mounting points carefully to avoid breaking clips
• Reuse original fasteners if undamaged; replace any broken clips before powering appliance

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

This replacement refrigerator door handle restores a secure, easy-to-grip pull for opening and closing the fridge. It matches the original mounting points for a clean, factory-fit appearance. What it does

• Replaces a cracked, loose, or broken refrigerator door handle so the door can be opened and closed safely.
• Provides a solid grip to help prevent slips and accidental drops.
• Restores proper clearance and alignment at the door edge for smooth operation.
• Helps maintain the appliance's original look and usability.

• One replacement refrigerator door handle.

• Installation requires removing the old handle and fastening the new handle to the existing mounting points; keep mounting screws and any trim pieces from the original assembly.
• Use basic hand tools; avoid over-tightening fasteners to prevent cracking the handle.
• Disconnect power only if instructed by the appliance manual for your specific model (most handle replacements do not require powering down).
• If the handle attaches under a trim or gasket, take care to reseat trim evenly to maintain door seal integrity.

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Size: 8-18ab x 0.5 inch.

This is a replacement drawer and door panel kit that restores the exterior appearance and function of the appliance's lower drawer and adjacent door. It fits as a direct-fit cosmetic panel kit to refresh worn or damaged fronts. What it does:

• Replaces damaged, cracked, or faded drawer and door panels to improve appearance
• Restores a flush, secure fit for the lower drawer and adjoining door
• Helps keep contents protected by providing a properly aligned front surface
• Matches OEM fit and attachment points for straightforward replacement

• Disconnect power before beginning any repairs and take care when moving heavy panels
• Installation may require removal of the drawer, trim screws, and clips; keep fasteners organized
• Use caution to avoid scratching surrounding surfaces and follow model-specific instructions