Kenmore Range 790.94214400 (79094214400, 790 94214400) Parts

This cabinet insulation panel helps reduce heat transfer and noise so your refrigerator reaches and keeps proper cooling more efficiently. It's a simple replacement that restores thermal barrier performance inside the cabinet. What it does:

• Replaces worn or damaged insulation to help maintain consistent internal temperatures
• Reduces compressor runtime and thermal cycling caused by heat gain
• Minimizes drafts, cold spots, and excess frost buildup around the cabinet
• Dampens vibration and operating noise for quieter performance

What's included:

• One cabinet insulation panel

Install notes:

• Disconnect power to the appliance before servicing to avoid shock hazards
• Access may require removing interior liners or trim; keep fasteners for reassembly
• Fit the panel into the cabinet cavity in the original orientation; secure as originally installed
• Inspect surrounding seals and components while the cabinet is open; replace any damaged parts

This genuine oven bake element heats the oven cavity for baking and roasting, restoring proper cooking temperatures and consistent results. Replaces a damaged or non-heating bake element to bring your oven back to service. What it does:

• Heats the oven cavity so food reaches and holds set temperatures
• Restores even baking and roasting when the oven fails to heat
• Replaces elements that show visible damage, burn-through, or no glow
• Works with electric ovens that use a separate bake heating element

• Disconnect power to the appliance at the breaker before starting work
• Handle the element carefully to avoid bending or damaging terminals
• Remove oven racks and access the element from inside the oven
• Verify proper fit and secure mounting; tighten terminal fasteners firmly and restore power to test

This replacement shield is a molded protective mounting shield that helps protect internal appliance components from debris and physical damage, keeping parts aligned for reliable operation and quieter performance. What it does:

• Covers and protects wiring, harnesses, or small components from contact and debris
• Helps maintain proper alignment of nearby parts to reduce wear and noise
• Prevents incidental interference between moving parts
• Restores intended component protection after damage or removal

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Handle plastic tabs and mounting points carefully to avoid breaking clips
• Reuse original fasteners if undamaged; replace any broken clips before powering appliance

0.6 fluid ounces

Note: ONE screw only, order as needed.

This door trim kit replaces the perimeter trim on the appliance door to restore a clean, factory finish. It covers and protects the door edges when the original trim is cracked, warped, or missing.

• Frames the door perimeter for a finished, uniform appearance
• Helps cover raw edges to prevent snags and rattling
• Replaces cracked, warped, or missing trim pieces
• Common signs include loose or missing trim, cosmetic damage, and gaps along the door edge

• Disconnect power (and gas, if applicable) and allow the appliance to cool before service
• Support the door; remove it if your service information recommends
• Carefully remove old trim; handle glass and sharp edges with cut-resistant gloves
• Align and secure the new trim; avoid overtightening fasteners and verify smooth door operation

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

Size: 8-18ab x 0.5 inch.