Kenmore Range 790.9611940B (7909611940B, 790 9611940B) Parts

This oven insulation surrounds the oven cavity to retain heat and protect nearby components and cabinetry. Replacing a burnt or deteriorated insulation blanket restores temperature stability and helps keep exterior surfaces cooler on your range during cooking.

• Minimizes heat loss for more consistent baking temperatures
• Shields wiring, controls, and adjacent cabinets from excessive heat
• Damaged insulation can cause long preheat times or trouble maintaining set temperature
• Exterior panels or control area may feel unusually hot, or a burnt odor may persist after spills

• Disconnect power at the breaker; shut off gas
• Allow the appliance to cool completely before service
• Access typically requires pulling the range and removing outer panels; note original routing and retainers for reassembly
• Handle insulation carefully; wear gloves, eye protection, and a dust mask to avoid irritation from fibers

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This oven door hinge restores secure, smooth opening and closing for a front-loading range or wall oven. It replaces a worn or damaged hinge to help the oven door align and operate safely. What it does:

• Supports the oven door and controls its pivot during opening and closing
• Helps keep the door properly aligned to maintain a tight seal
• Replaces a bent, broken or worn hinge that can cause door sag or uneven closing
• Reduces binding or sticking when the door is moved

• Disconnect power to the appliance before starting any repair to avoid electrical shock
• Follow the oven manufacturer's service instructions—door springs and hinges can be under tension
• Use appropriate tools and an assistant if needed to support the door during removal and installation

This shield panel protects internal components and helps direct airflow inside the appliance, replacing a bent, corroded or missing cover to restore proper airflow and reduce contact with moving parts. What it does:

• Covers and protects evaporator and electrical components from debris and accidental contact
• Directs airflow for more consistent temperature inside the compartment
• Stops rattling or interference caused by a loose or damaged shield
• Helps prevent ice buildup and moisture contact when properly seated

• Disconnect power before servicing to avoid shock or injury
• Handle edges carefully — metal panels can be sharp
• Basic hand tools are typically required; follow the appliance service manual for removal and reinstallation
• Secure all fasteners to prevent vibration or contact with moving parts

This insulator is a molded protective cushion that reduces vibration and protects nearby components from wear or contact. It helps keep parts stable and minimizes noise for smoother appliance operation. What it does:

• Cushions components to reduce vibration and rattling
• Protects wiring, tubing, and panels from abrasion and impact
• Helps maintain proper spacing between parts to prevent rubbing
• Can reduce operational noise caused by loose or contacting parts

• One insulator

• Disconnect power to the appliance before starting any repair
• Remove the access panel(s) needed to reach the mounting area; retain fasteners
• Press or slide the insulator into the correct position; it fits snugly and secures the component
• If removal requires cutting old adhesive or clips, replace with equivalent fasteners or adhesives approved by the manufacturer

This small push-in plug button caps the opening in an oven bottom to keep the cavity clean and finished-looking. It prevents food and debris from falling into the oven base and restores a secure, even interior surface. What it does:

• Covers and seals the hole in the oven bottom to prevent debris buildup
• Helps maintain a finished appearance and reduces hotspots around openings
• Stops loose items from dropping into the oven base and interfering with components
• Simple, low-profile cap designed for a snug, friction-fit installation

• Turn the oven off and allow it to cool completely before installing
• Press the plug button firmly into the opening until it seats flush
• Use a non-marring tool if needed to avoid scratching the oven surface
• Replace with the correct OEM part if the plug does not fit securely or is damaged