Kenmore Range 790.96219409 (79096219409, 790 96219409) Parts

Note: ONE screw only, order as needed.

Color: Black

Replacement black control knob that restores grip and control for an appliance selector, timer, or temperature shaft. Simple push-on fit and textured edge make it easier to turn controls and replace worn or missing knobs. What it does:

• Provides a firm grip for turning selector, timer, or temperature controls
• Replaces cracked, faded, or missing knobs that are hard to adjust
• Seats onto the control shaft to restore accurate, tactile feedback
• Helps prevent slipping while setting temperature or cycle selections

• Most installations are simple: pull the old knob straight off and push the replacement onto the shaft until fully seated
• If the knob is difficult to remove, use a gentle, steady pull—avoid twisting hard or using excessive force
• Disconnect power to the appliance before servicing controls to reduce risk of shock or injury

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This oven door hinge restores secure, smooth opening and closing for a front-loading range or wall oven. It replaces a worn or damaged hinge to help the oven door align and operate safely. What it does:

• Supports the oven door and controls its pivot during opening and closing
• Helps keep the door properly aligned to maintain a tight seal
• Replaces a bent, broken or worn hinge that can cause door sag or uneven closing
• Reduces binding or sticking when the door is moved

• Disconnect power to the appliance before starting any repair to avoid electrical shock
• Follow the oven manufacturer's service instructions—door springs and hinges can be under tension
• Use appropriate tools and an assistant if needed to support the door during removal and installation

This ceramic catalyst oven vent fits behind the oven broiler to help vent and break down cooking residues and odors at high temperatures, keeping oven air cleaner during cooking and self-clean cycles. It's a direct-replacement part when the original is cracked, clogged, or missing. What it does:

• Provides a heat-resistant vent surface that helps oxidize grease and odors that pass through the vent during use
• Helps maintain proper oven ventilation for consistent cooking and cleaner internal airflow
• Commonly replaced when the vent is cracked, glazed-over, excessively discolored, or emits persistent odors
• Works as part of the oven's venting system—does not affect electronic controls

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Allow the oven to cool fully; this part is installed inside the oven cavity or broiler area and may require removing racks or access panels
• Handle with care—ceramic components can crack if dropped or flexed; wear gloves to protect hands and avoid fingerprints on ceramic surfaces

This shield panel protects internal components and helps direct airflow inside the appliance, replacing a bent, corroded or missing cover to restore proper airflow and reduce contact with moving parts. What it does:

• Covers and protects evaporator and electrical components from debris and accidental contact
• Directs airflow for more consistent temperature inside the compartment
• Stops rattling or interference caused by a loose or damaged shield
• Helps prevent ice buildup and moisture contact when properly seated

• Disconnect power before servicing to avoid shock or injury
• Handle edges carefully — metal panels can be sharp
• Basic hand tools are typically required; follow the appliance service manual for removal and reinstallation
• Secure all fasteners to prevent vibration or contact with moving parts

This is a replacement Simmer Select push button for stove/oven control panels. It restores the Simmer Select control's functionality and appearance so the range responds correctly and looks like new. What it does:

• Serves as the user-facing push button for the Simmer Select function on the control panel
• Allows selection of simmer cooking setting when the control switch behind the button is engaged
• Replaces cracked, faded, or missing buttons that stick or fail to make contact
• Helps resolve symptoms such as an unresponsive Simmer Select control, broken button cap, or cosmetic damage

• Disconnect power to the appliance before starting any repair
• Remove the control panel or console to access the button
• Install by snapping the button onto the corresponding control shaft; do not force or bend plastic retainers
• Verify proper operation before reassembling; keep small parts and fasteners secure