Kenmore Refrigerator 795.51313012 (79551313012, 795 51313012) Parts

This is the water injector tube for select refrigerators. It routes water from the supply system into the appropriate internal channel, helping ensure proper flow to the ice maker or dispenser and preventing leaks at the connection point.

• Directs water from the valve/supply line into the refrigerator's internal water path
• Helps restore proper ice maker/dispenser filling
• Common symptoms: leaking at the rear/under the unit, poor or no ice production, slow or no dispenser flow

• Unplug the refrigerator and shut off the water supply before service
• Have a towel ready to catch residual water from the line
• Note tube routing and connection points before removal; push-to-connect fittings may be present
• After installation, turn water on and check all joints for leaks

This controller assembly is the appliance's main electronic control that manages cycles and user inputs to restore proper control operation. Replace a failing controller assembly to address unresponsive controls, incorrect cycle behavior, or intermittent errors. What it does:

• Manages cycle selection, timing, and communication between sensors and motors to coordinate appliance operation.
• Interprets user inputs from the front panel and sends commands to other components.
• Failure may cause unresponsive buttons, unexpected error codes, stalled or incorrect cycles, or an appliance that won't start.
• Replacing the assembly often resolves control-board–related faults when diagnostics point to the main controller.

• Disconnect power (unplug or switch off breaker) before removing the old assembly to avoid shock or damage.
• Handle the board and connectors carefully; avoid static discharge and cradle the assembly by its edges.
• Match the replacement to the exact part number and transfer any brackets, grounding straps, or button housings as needed.

Refrigerator dispenser lever that controls ice and water dispensing through the door. Replace if cracked, broken, loose, or missing for proper function.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

Removable door bin for butter, cheese, and small dairy items. Replaces cracked, broken, or missing bins to restore organized door storage.

This lower cover assembly replaces the damaged or missing lower access cover on your appliance to protect internal components and restore a finished appearance. It helps keep lint, debris and moisture away from cabinet internals. What it does:

• Protects internal wiring, ducts and components by sealing the lower cabinet area
• Restores the appliance's finished look when the existing cover is cracked, broken or missing
• Helps reduce rattling or vibration caused by loose or damaged lower trim
• Prevents debris and pet hair from entering serviceable openings

• Disconnect power (and water, if applicable) before starting any repair
• May require removal of the toe panel or front access panel; keep fasteners for reuse
• Use basic hand tools; handle plastic tabs gently to avoid breakage

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

This motor start/run capacitor helps the appliance motor or compressor start and run more reliably, restoring proper motor performance and reducing symptoms caused by a weak or failed capacitor. What it does:

• Provides the momentary electrical boost motors or compressors need to start
• Helps maintain stable motor operation during run cycles
• Resolves symptoms like motors that hum but won't start, intermittent starting issues, or cycling problems
• Replaces a worn or failed capacitor to restore consistent performance

• One replacement capacitor as shown

• Disconnect power before servicing and verify the appliance is de-energized
• Capacitors can hold charge — discharge safely before touching terminals
• Match terminal type and mounting location to the original part; do not force connections

Tray cover for refrigerators. Installs on top of storage trays or compartments. Replace if cracked, broken, or missing to restore appearance.

Secures refrigerator door in fully closed and aligned positions. Replace if stopper is cracked, broken, or door won't stay aligned properly.

Replace a cracked, broken, or missing refrigerator door bin. Restores secure storage for bottles, condiments, and small items on door shelves.

This is a rear handle end cap that attaches to the back side of a refrigerator door handle. It provides a finished appearance and secures the handle assembly to the door. Replace this cap if it is cracked, broken, or missing, which can cause the handle to feel loose or look incomplete.

This noise damper reduces vibration and rattling sounds from refrigerant lines in your refrigerator. It cushions the copper tubing against the cabinet to prevent metal-on-metal contact that creates annoying noises. Install this damper if your refrigerator makes clicking, rattling, or vibrating sounds, especially when the compressor cycles on and off.

This is the display PCB assembly located behind the front dispenser panel of the refrigerator. It manages user inputs for temperature adjustment, ice and water dispensing, and display readouts. Replace this board if the display is flickering, not responding to button presses, or if the dispenser functions have become erratic or non-functional.