Kenmore Refrigerator 795.71012011 (79571012011, 795 71012011) Parts

Refrigerator shelf assembly that replaces a damaged or missing internal shelf, restoring flat, secure storage for food and containers. Helps keep items level and organized inside the fridge. What it does

• Replaces a broken, cracked, or missing refrigerator shelf to restore usable storage space.
• Provides a flat, stable surface for jars, bowls, and containers so items won't tip or slide.
• Prevents food from sagging between compartments and improves organization and accessibility.
• Matches factory-fit shelf mounts and seating points for correct alignment when installed.

• Remove all items from the shelf area before installing; handle glass or trim with care and wear protective gloves if needed.
• Slide or seat the shelf into the factory supports or track until it clicks or sits flat; some models require lifting slightly to engage rear tabs.
• No electrical disconnect is typically required, but follow the refrigerator owner's manual and disconnect power if instructed for your model.
• If the shelf has clips or trim pieces, verify they are properly engaged and undamaged before use.

This center hinge assembly supports the middle/center door on compatible refrigerators, restoring proper alignment and smooth opening. Replaces a worn or damaged hinge to help the door close evenly and reduce rubbing or sagging. What it does

• Provides the pivot point that keeps the center door aligned and balanced.
• Allows smooth door movement and helps maintain an even door gap.
• Corrects symptoms like door sagging, uneven gaps, rubbing, or doors that don't close fully.
• Works with factory mounting points for a direct replacement.

• Disconnect power to the appliance and empty or support the door before starting.
• Support the door securely while removing and installing the hinge to prevent injury or damage.
• Use common hand tools and follow the appliance service manual for door removal and reinstallation.
• Check door alignment and gasket seating after installation; adjust hinge position as needed per manufacturer instructions.

This multi duct directs airflow inside the appliance to maintain proper ventilation and operation. Replacing a damaged duct restores directed air movement and helps prevent exhaust leaks or reduced performance. What it does:

• Routes air between internal components to support heating, cooling, or venting systems
• Prevents exhaust or recirculation air from leaking into the cabinet
• Helps maintain consistent airflow for proper appliance operation
• Can reduce abnormal airflow noise when intact and correctly seated

• Disconnect power (and gas, if applicable) before beginning work
• Handle plastic/metal ducting carefully to avoid cracking or sharp edges
• Verify correct duct orientation and secure all clips or fasteners for an airtight fit

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

This connector cover is the small trim piece that shields and conceals the connection area on your refrigerator. Replacing a cracked or missing cover restores a clean, finished look and helps protect connectors from dust and accidental snags.

• Covers and protects the wiring and/or tubing connector cavity
• Helps keep debris out of the connection area
• Maintains proper routing and prevents snagging of harnesses
• Common signs it's needed: cracked or missing cover, exposed connectors, cover won't stay attached, cosmetic damage

• Disconnect power and turn off the water supply before beginning
• Remove any retaining screw(s) or release tabs to take off the old cover
• Position the new cover, ensuring wires/tubing aren't pinched; secure with original hardware
• Restore power/water and confirm the cover is fully seated

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

A replacement cover frame that restores the finished look and protection around the appliance control area. Replaces a cracked, warped, or scratched trim to keep controls secure and maintain appearance. What it does:

• Covers and protects the control panel edges from bumps, spills, and wear
• Keeps switches and buttons aligned and held in place
• Restores the appliance's finished appearance when the original frame is damaged
• Helps prevent debris from entering the control cavity

• Disconnect power to the appliance before beginning any work
• Remove any outer trim or control panel fasteners to access the existing frame
• Handle the part carefully to avoid scratching the finish during install

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

This power control board assembly replaces a failed main control module to restore a unit's electronic control and power distribution. It helps the appliance respond correctly to user inputs and manage timed cycles. What it does:

• Manages power to key components and coordinates control signals across the appliance
• Replaces boards that cause no response, intermittent power loss, or unresponsive touch/knob controls
• Can correct erratic behavior tied to control logic or failed onboard components
• Works as the factory-style board designed for direct swap with the original unit

• Disconnect power before starting and follow OEM grounding precautions to avoid shock or board damage
• Handle the board by its edges; avoid touching soldered components or connector pins
• Verify connectors and wire harness locations match before securing; do not force connectors

Replacement guide assembly that secures and aligns internal TV components and cabinet panels to restore proper fit and reduce movement. Use this guide when a panel or internal module sits loose or causes vibration or rattling. What it does:

• Positions and supports internal components and circuit boards to maintain correct alignment
• Secures cabinet panels and trim to prevent gaps and movement
• Reduces vibration and rattling caused by loose internal parts
• Helps maintain proper routing for internal cables and connectors

• Disconnect power and remove the TV from its stand or wall before starting repair
• Use proper tools and keep screws/fasteners organized; handle panels and the display with care
• Follow the OEM service manual for disassembly/reassembly steps and torque specs

This is a replacement mounting screw used to secure appliance panels, trim or components. It restores proper attachment to reduce vibration and rattling and helps keep removable parts firmly in place during operation. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Restores secure fit when original screw is missing, loose, or stripped
• Reduces rattling and vibration caused by loose hardware
• Helps maintain proper alignment of removable covers and control panels

• Disconnect power and water before starting any repair
• Verify size and thread match the original screw before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten — overtightening can strip threads or crack plastic parts
• Keep small parts away from children and pets