Kenmore Refrigerator 795.71012012 (79571012012, 795 71012012) Parts

The Ice Bucket is an OEM part for LG refrigerators. It is a component that stores ice from the icemaker in the freezer. The ice bucket is designed to fit within the refrigerator, providing a convenient and accessible storage solution for ice.

Causes of a bad Ice Bucket can include wear and tear over time, or damage to the bucket or its components due to mishandling or impact. Please note, this is just the ice bucket. It does not include the auger or auger motor.

Symptoms of a bad Ice Bucket include:

• Cracks or damage to the bucket
• Difficulty in fitting the bucket securely in place
• Ice not being stored properly or spilling

This OEM LG part is also compatible with Sears/Kenmore.

This connector cover is the small trim piece that shields and conceals the connection area on your refrigerator. Replacing a cracked or missing cover restores a clean, finished look and helps protect connectors from dust and accidental snags.

• Covers and protects the wiring and/or tubing connector cavity
• Helps keep debris out of the connection area
• Maintains proper routing and prevents snagging of harnesses
• Common signs it's needed: cracked or missing cover, exposed connectors, cover won't stay attached, cosmetic damage

• Disconnect power and turn off the water supply before beginning
• Remove any retaining screw(s) or release tabs to take off the old cover
• Position the new cover, ensuring wires/tubing aren't pinched; secure with original hardware
• Restore power/water and confirm the cover is fully seated

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

A replacement cover frame that restores the finished look and protection around the appliance control area. Replaces a cracked, warped, or scratched trim to keep controls secure and maintain appearance. What it does:

• Covers and protects the control panel edges from bumps, spills, and wear
• Keeps switches and buttons aligned and held in place
• Restores the appliance's finished appearance when the original frame is damaged
• Helps prevent debris from entering the control cavity

• Disconnect power to the appliance before beginning any work
• Remove any outer trim or control panel fasteners to access the existing frame
• Handle the part carefully to avoid scratching the finish during install

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

Replacement guide assembly that secures and aligns internal TV components and cabinet panels to restore proper fit and reduce movement. Use this guide when a panel or internal module sits loose or causes vibration or rattling. What it does:

• Positions and supports internal components and circuit boards to maintain correct alignment
• Secures cabinet panels and trim to prevent gaps and movement
• Reduces vibration and rattling caused by loose internal parts
• Helps maintain proper routing for internal cables and connectors

• Disconnect power and remove the TV from its stand or wall before starting repair
• Use proper tools and keep screws/fasteners organized; handle panels and the display with care
• Follow the OEM service manual for disassembly/reassembly steps and torque specs

This is a replacement mounting screw used to secure appliance panels, trim or components. It restores proper attachment to reduce vibration and rattling and helps keep removable parts firmly in place during operation. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Restores secure fit when original screw is missing, loose, or stripped
• Reduces rattling and vibration caused by loose hardware
• Helps maintain proper alignment of removable covers and control panels

• Disconnect power and water before starting any repair
• Verify size and thread match the original screw before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten — overtightening can strip threads or crack plastic parts
• Keep small parts away from children and pets

This is a replacement mounting bracket that secures internal appliance components to the cabinet frame, restoring proper alignment and support for moving parts. It helps reduce vibration and prevents loose or sagging assemblies. What it does:

• Provides a stable mounting point for internal components to maintain correct positioning
• Helps stop rattling, knocking, or vibration caused by loose fittings
• Restores support for panels, assemblies, or mechanical linkages that rely on the bracket
• Useful when original bracket is bent, cracked, or otherwise damaged

• Follow manufacturer service manual for correct placement and fastener torque
• Use proper tools and retain all screws/fasteners; replace damaged fasteners as needed
• Disconnect power before accessing internal components to avoid shock or injury