Kenmore Refrigerator 795.71024012 (79571024012, 795 71024012) Parts

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This main PCB power control board is the appliance's electronic control module that manages power distribution and coordinates core functions—replacing a faulty board restores proper electronic control and responsive operation. What it does:

• Regulates and distributes electrical power to the appliance's subsystems
• Controls electronic functions and timing for cycles and user commands
• Processes user-interface inputs and sends signals to motors, valves, heaters, or compressors
• Common symptoms of a failing board include no power or unresponsive controls, intermittent operation, or error codes related to electronics

• Always disconnect power before servicing; verify the appliance is fully de-energized
• Take note of connector locations and wire routing before removal for correct reinstallation
• Handle the PCB by its edges and avoid static discharge; do not touch component leads

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This rail guide assembly supports and guides a sliding refrigerator drawer/bin so it opens and closes smoothly. Replace a cracked or worn rail to restore proper alignment and prevent jamming or the drawer coming off its track. What it does:

• Attaches to the cabinet wall to support the sliding drawer/bin
• Provides a smooth track for extension and retraction
• Keeps the drawer level and aligned to prevent binding or rubbing
• Failure symptoms include a hard-to-open/close drawer, tilting on one side, popping off track, or visible cracks/broken tabs on the rail

• One rail guide assembly

• Disconnect power and remove the affected drawer/bin (and any glass shelf above) before starting
• Remove mounting screws, note their locations, and lift out the damaged rail
• Position the new rail, reinstall screws, and ensure the drawer engages the slide correctly
• Use caution around sharp edges; test drawer movement before reloading

This is a replacement mounting screw used to secure appliance panels, trim or components. It restores proper attachment to reduce vibration and rattling and helps keep removable parts firmly in place during operation. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Restores secure fit when original screw is missing, loose, or stripped
• Reduces rattling and vibration caused by loose hardware
• Helps maintain proper alignment of removable covers and control panels

• Disconnect power and water before starting any repair
• Verify size and thread match the original screw before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten — overtightening can strip threads or crack plastic parts
• Keep small parts away from children and pets

This is a replacement mounting bracket that secures internal appliance components to the cabinet frame, restoring proper alignment and support for moving parts. It helps reduce vibration and prevents loose or sagging assemblies. What it does:

• Provides a stable mounting point for internal components to maintain correct positioning
• Helps stop rattling, knocking, or vibration caused by loose fittings
• Restores support for panels, assemblies, or mechanical linkages that rely on the bracket
• Useful when original bracket is bent, cracked, or otherwise damaged

• Follow manufacturer service manual for correct placement and fastener torque
• Use proper tools and retain all screws/fasteners; replace damaged fasteners as needed
• Disconnect power before accessing internal components to avoid shock or injury

Replacement guide assembly that secures and aligns internal TV components and cabinet panels to restore proper fit and reduce movement. Use this guide when a panel or internal module sits loose or causes vibration or rattling. What it does:

• Positions and supports internal components and circuit boards to maintain correct alignment
• Secures cabinet panels and trim to prevent gaps and movement
• Reduces vibration and rattling caused by loose internal parts
• Helps maintain proper routing for internal cables and connectors

• Disconnect power and remove the TV from its stand or wall before starting repair
• Use proper tools and keep screws/fasteners organized; handle panels and the display with care
• Follow the OEM service manual for disassembly/reassembly steps and torque specs