Kenmore Refrigerator 795.71032010 (79571032010, 795 71032010) Parts

This rail guide assembly restores smooth, stable sliding for a refrigerator/freezer drawer or shelf drawer, helping the drawer track properly and reducing rubbing or sticking during use. What it does:

• Replaces a worn or damaged drawer slide rail to restore proper alignment and smooth movement
• Helps stop drawers from sticking, binding, scraping, or falling out of track
• Supports the drawer weight and guides it in and out evenly
• Reduces noise caused by misaligned or worn rails

• Disconnect power (and water, if applicable) before servicing the appliance
• Remove the drawer or shelving to access the rail; retain fasteners for reuse unless new ones are provided
• Inspect matching rail on the opposite side; replace both sides if both show wear for best performance

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement door gasket assembly seals the refrigerator door to help maintain proper temperature and reduce energy loss. It restores the seal around the door edge for better cooling performance and food preservation. What it does:

• Creates an airtight seal around the refrigerator door to limit cold air escape
• Helps maintain consistent internal temperature for food safety
• Reduces frost buildup and excessive compressor run time when working properly
• Addresses symptoms such as warm spots near the door, visible gaps, or persistent condensation

• One door gasket assembly

• Inspect the door and mounting channel for debris before installing; clean with mild detergent and dry completely
• Gasket typically stretches into a channel and secures around the door perimeter—avoid sharp tools that can damage the seal
• For best results, install at room temperature; warm the gasket gently if needed to ease fitting

Note: Left Rail Cap

This replacement door basket mounts on the refrigerator door to hold bottles, jars, and condiments. It restores secure, easy-access storage when the original bin is cracked, damaged, or missing.

• Attaches to the inner door rails to organize items on the door
• Keeps contents in place as the door opens and closes
• Replaces a cracked, broken, warped, or missing bin
• Symptoms include broken tabs, bin won't stay seated, or reduced door storage

• Remove items from the old bin; lift up to release it from the door rails
• Align the new basket's hooks with the door slots and lower until fully seated
• Confirm the bin is level and secure before loading
• No tools typically required; avoid overloading to prevent damage

This rail guide assembly replaces a worn or broken slide rail that supports smooth movement of a drawer or component. Restores proper alignment and helps the drawer glide quietly and evenly. What it does:

• Guides and supports the drawer or sliding component along its track.
• Replaces damaged or bent rail sections that cause sticking or uneven movement.
• Reduces scraping, grinding, or noisy operation from a faulty guide.
• Helps restore proper alignment to prevent binding or partial closure.

• One rail guide assembly.

• Disconnect power (and water if applicable) and follow appliance-specific disassembly steps before replacing the rail.
• Basic hand tools are typically required; avoid forcing components to prevent breakage.
• Keep fasteners and any removed parts organized for reassembly.

This door gasket assembly replaces a worn or damaged refrigerator door seal to restore an airtight closure and help maintain proper cooling. It fits the door's perimeter and creates the seal between the cabinet and door. What it does:

• Seals the refrigerator door to retain cold air and improve temperature stability.
• Prevents warm air intrusion that can cause frost buildup or increased energy use.
• Helps reduce condensation and water leaks around the door area.
• Restores proper door alignment and closing when old gasket is torn, stretched, or deformed.

• Unplug the appliance and remove food from the door area before starting.
• Work with the door propped or supported; follow OEM removal steps for existing gasket tabs or clips.
• Gently warm and flex the new gasket if needed for easier seating; avoid sharp tools that can puncture it.
• After installation, check the seal around the full perimeter and allow a short run cycle to verify proper operation.

This display power control board assembly powers and controls the appliance's user interface so lights, touchpads and status displays operate correctly. It replaces a failed display board to restore normal panel behavior and feedback. What it does

• Supplies power and signal control to the front display and indicator lights.
• Manages button/touch inputs and display output for the control console.
• Common symptom: display or control lights are dim, flicker, or not lighting.
• Common symptom: control panel is unresponsive, buttons do not register, or display shows no information.

• Disconnect power (unplug appliance or shut off breaker) before any service.
• Handle the board carefully and avoid static discharge; use anti-static precautions if available.
• Verify connector orientation and seating before reassembly; do not force connectors.

Note: Right Rail Cap 

This hinge assembly replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. It helps stop sagging doors, noisy movement, and improper sealing for better cooling performance. What it does:

• Supports and pivots the refrigerator door for correct alignment and even sealing
• Replaces broken, bent, or worn hinge hardware that causes door sag or misalignment
• Reduces rubbing, grinding, or noisy hinge movement when opening or closing
• Helps restore proper door closure to prevent cold air loss and temperature issues

• Unplug the appliance and support the door before removing hinge hardware to prevent injury or damage
• Transfer any mounting screws or brackets only if specified by the OEM; replace visibly damaged fasteners
• Tighten mounting fasteners to secure the hinge but avoid over-torquing; confirm door alignment after installation

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This is a factory-style screw used to secure components and panels on compatible LG appliances. It restores proper fit and reduces movement where a missing or stripped screw causes parts to sit loose. What it does:

• Fastens panels, brackets, or trim to appliance chassis to restore secure attachment
• Stops rattling or vibration caused by loose or missing fasteners
• Helps maintain proper alignment of removable parts for safe operation
• Serves as a direct replacement when the original screw is lost or damaged

• Screw

• Use the matching screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent damage to threads or plastic parts
• Replace only with the specified OEM screw to ensure fit and function
• Disconnect power to the appliance before accessing internal components when applicable