Kenmore Refrigerator 795.71033110 (79571033110, 795 71033110) Parts

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

This damper assembly controls airflow between compartments to help maintain consistent refrigerator temperatures and restore proper air distribution. It replaces a damaged or stuck damper that interferes with cooling balance. What it does:

• Regulates fresh food/freezer airflow by opening and closing the inlet
• Helps correct uneven temperatures or reduced cooling caused by a stuck or broken damper
• Stops unwanted drafts when the damper is closed
• Operates with the fridge's control system to respond to temperature changes

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels or shelving to reach the damper housing
• Handle plastic parts and wiring gently; avoid forcing connectors

This tray cover assembly replaces a cracked or missing ice tray cover to keep ice protected and help the ice bin stack and slide correctly. It restores a clean seal and simple access to the ice storage area. What it does:

• Covers and protects ice in the ice bin from odors and debris
• Helps maintain proper alignment and sliding action of the ice bin
• Prevents spills and reduces ice melting caused by gaps or damage
• Commonly replaced when the cover is cracked, warped, or missing

• One tray cover assembly

• Disconnect power to the appliance before servicing to avoid injury
• Remove the ice bin and any remaining ice before installing the cover
• Handle plastic components carefully to avoid cracking; align tabs and slides before seating

This door gasket assembly seals a refrigerator/freezer door to keep cold air in and humidity out, helping maintain proper temperature and reduce frost buildup. It restores a tight door seal for better efficiency and food preservation. What it does:

• Replaces a worn, torn, or warped door seal that lets cold air escape
• Helps stop excessive frost or ice buildup and reduces condensation
• Improves cooling efficiency and can help stabilize internal temperature
• Reduces rattling or uneven door closure caused by a damaged gasket

• One door gasket assembly

• Disconnect power and remove stored food before starting the repair
• Inspect the door and sealing surface for damage or debris; clean before installing
• Seat the gasket evenly into the channel and work around the perimeter to avoid twists
• If needed, warm the gasket slightly for easier fitting; avoid open flames or excessive heat

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

Note: 90 degree elbow coupler (Fits 1/4" diameter tubing on each end) For 5/16" elbow connector, order part# 4932JA3009B.

The Water Line Union is an OEM part for LG refrigerators. This component connects sections of the water line, ensuring a secure and leak-free passage of water to the refrigerator's icemaker and water dispenser. It is an elbow tube union connector, which connects two tubes at a 90-degree angle.

Causes of a bad water line union can include wear and tear from frequent use, damage from high water pressure, or deterioration due to mineral buildup and age. A compromised union can lead to water leaks and disruption in the water supply.

Symptoms of a bad Water Line Union include:

• Water leaks around the connection points
• Reduced water flow to the icemaker or water dispenser
• Puddles or moisture near the refrigerator
• Unusual noises from the water line

This OEM LG part is also compatible with Sears/Kenmore.

This sheathed defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice-clogged coils, warm spots, and noisy fan interference.

• Melts frost from the evaporator coil during the defrost cycle to maintain proper airflow
• Symptoms of failure: persistent ice on the back panel, weak cooling, or the evaporator fan striking ice
• A failed heater can cause long run times and temperature swings
• Replace if the element tests open/short or shows visible damage

• Disconnect power before service; allow components to warm to reduce risk of cracking brittle plastics
• Remove shelves and the evaporator cover; carefully defrost ice—do not chip or pry against the fins
• Transfer original clips/insulators if present; route wires as original and make firm electrical connections
• After reassembly, ensure the drain area is clear and the fan spins freely

This Door Basket Assembly restores secure, convenient storage on your refrigerator door. Replace a cracked or missing bin to keep items organized and help the door close and seal properly. What it does:

• Provides storage space on the inner door for bottles, condiments, and small items
• Helps keep items contained so they don't shift or interfere with the door gasket
• Restore function when the original bin is cracked, chipped, warped, or will not stay seated
• Common symptoms: loose or broken bin, items falling from the door, difficulty closing the door

• 1 door basket assembly

• Unload the door; lift the damaged bin straight up and out of the door-liner slots
• Align the replacement with the mounting tabs and slide or press down until fully seated on both sides
• Do not force; re-seat if resistance is felt to avoid breaking the tabs
• Verify a secure fit before reloading and avoid overloading the bin

• Many refrigerators use multiple, position-specific door bins. Compare the shape and mounting tabs to your original before ordering.

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary