Kenmore Refrigerator 795.71036010 (79571036010, 795 71036010) Parts

This rail guide assembly supports and guides a sliding drawer/rack along its track so it opens and closes smoothly. Replacing a worn or broken guide restores proper alignment and motion, helping prevent sticking, jamming, or uneven travel.

• Supports and stabilizes the drawer/rack on its slide rail
• Helps ensure smooth, straight opening and closing
• Can address issues like binding, noise, or misalignment
• Replaces cracked, warped, or broken guide components

• Disconnect power and, if applicable, shut off water before servicing
• Remove the drawer/rack and retain any reusable hardware
• Install the new guide in the same orientation as the original
• Test movement for smooth travel before fully reassembling

This tray cover assembly replaces a cracked or missing ice tray cover to keep ice protected and help the ice bin stack and slide correctly. It restores a clean seal and simple access to the ice storage area. What it does:

• Covers and protects ice in the ice bin from odors and debris
• Helps maintain proper alignment and sliding action of the ice bin
• Prevents spills and reduces ice melting caused by gaps or damage
• Commonly replaced when the cover is cracked, warped, or missing

• One tray cover assembly

• Disconnect power to the appliance before servicing to avoid injury
• Remove the ice bin and any remaining ice before installing the cover
• Handle plastic components carefully to avoid cracking; align tabs and slides before seating

This rail holder secures a door rail to keep the door aligned and stable, restoring smooth opening and closing. It's a direct-fit replacement designed to match the OEM mounting points and restore proper door support. What it does:

• Holds the door rail in place so the door stays aligned and operates smoothly
• Prevents rail movement that can cause rubbing, rattling, or uneven closing
• Restores proper support where a worn or broken holder causes loose or sagging rails
• Helps eliminate noise and misalignment symptoms linked to a failed rail support

• One rail holder

• Disconnect power and follow the appliance manufacturer's service instructions before beginning repair
• Remove surrounding trim or screws as needed to access the rail; keep fasteners for reassembly
• Handle door components carefully to avoid damaging glass or seals; a second pair of hands may help
• Verify part orientation and fit before tightening fasteners;

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

Note: 90 degree elbow coupler (Fits 1/4" diameter tubing on each end) For 5/16" elbow connector, order part# 4932JA3009B.

The Water Line Union is an OEM part for LG refrigerators. This component connects sections of the water line, ensuring a secure and leak-free passage of water to the refrigerator's icemaker and water dispenser. It is an elbow tube union connector, which connects two tubes at a 90-degree angle.

Causes of a bad water line union can include wear and tear from frequent use, damage from high water pressure, or deterioration due to mineral buildup and age. A compromised union can lead to water leaks and disruption in the water supply.

Symptoms of a bad Water Line Union include:

• Water leaks around the connection points
• Reduced water flow to the icemaker or water dispenser
• Puddles or moisture near the refrigerator
• Unusual noises from the water line

This OEM LG part is also compatible with Sears/Kenmore.

This sheathed defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice-clogged coils, warm spots, and noisy fan interference.

• Melts frost from the evaporator coil during the defrost cycle to maintain proper airflow
• Symptoms of failure: persistent ice on the back panel, weak cooling, or the evaporator fan striking ice
• A failed heater can cause long run times and temperature swings
• Replace if the element tests open/short or shows visible damage

• Disconnect power before service; allow components to warm to reduce risk of cracking brittle plastics
• Remove shelves and the evaporator cover; carefully defrost ice—do not chip or pry against the fins
• Transfer original clips/insulators if present; route wires as original and make firm electrical connections
• After reassembly, ensure the drain area is clear and the fan spins freely

This sub PCB assembly is an electronic control board used in select LG appliances. It manages signals and low-voltage power for a specific feature or module, helping restore normal operation when the original board becomes unresponsive or fails.

• Provides low-voltage control for the designated function or user interface
• Communicates with the main control to execute settings and cycles
• Helps resolve symptoms such as unresponsive controls, blank/flickering display, intermittent operation, or related error codes
• Supports reliable operation of the affected subsystem after replacement

• Disconnect power at the breaker; shut off gas/water if applicable
• Use ESD protection and handle the board by the edges
• Photograph wire locations; transfer connectors one at a time to avoid miswiring
• Follow the service sheet for any required option-code entry, reset, or diagnostic check after installation

This Door Basket Assembly restores secure, convenient storage on your refrigerator door. Replace a cracked or missing bin to keep items organized and help the door close and seal properly. What it does:

• Provides storage space on the inner door for bottles, condiments, and small items
• Helps keep items contained so they don't shift or interfere with the door gasket
• Restore function when the original bin is cracked, chipped, warped, or will not stay seated
• Common symptoms: loose or broken bin, items falling from the door, difficulty closing the door

• 1 door basket assembly

• Unload the door; lift the damaged bin straight up and out of the door-liner slots
• Align the replacement with the mounting tabs and slide or press down until fully seated on both sides
• Do not force; re-seat if resistance is felt to avoid breaking the tabs
• Verify a secure fit before reloading and avoid overloading the bin

• Many refrigerators use multiple, position-specific door bins. Compare the shape and mounting tabs to your original before ordering.

This small retaining clip secures its mating component within the refrigerator assembly, keeping parts properly seated and reducing vibration. Replacing a damaged or missing clip helps restore a snug fit and reliable operation of the attached piece.

• Holds the designated part firmly in place within the assembly
• Maintains proper alignment to prevent movement or rattling
• Helps ensure panels, ducts, or lines stay secured during use
• Symptoms can include loose or sagging parts, vibration noises, or components that won't stay attached

• Disconnect power; if working near the water system, also shut off the water supply
• Note the original orientation and placement before removal
• Fully seat the mating component, then press the new clip into place without forcing
• Check operation before reassembly