Kenmore Refrigerator 795.71049010 (79571049010, 795 71049010) Parts

A single mounting screw used to secure panels, brackets, or components in place so assemblies stay stable during normal appliance use. Simple replacement for stripped or missing fasteners. What it does:

• Secures panels, trim, brackets or interior components to prevent rattling or movement
• Restores proper fit and alignment after service or accidental damage
• Helps reattach parts removed during maintenance or part replacement
• Small, durable fastener designed for appliance interior mounting applications

• Use the correct screw driver or bit to avoid stripping the head
• Match screw length and thread engagement to the original location before tightening
• Tighten until snug—do not overtighten to avoid cracking plastic or damaging threads
• Disconnect power and follow appliance safety procedures before performing repairs

This rail guide assembly supports and guides a sliding drawer/rack along its track so it opens and closes smoothly. Replacing a worn or broken guide restores proper alignment and motion, helping prevent sticking, jamming, or uneven travel.

• Supports and stabilizes the drawer/rack on its slide rail
• Helps ensure smooth, straight opening and closing
• Can address issues like binding, noise, or misalignment
• Replaces cracked, warped, or broken guide components

• Disconnect power and, if applicable, shut off water before servicing
• Remove the drawer/rack and retain any reusable hardware
• Install the new guide in the same orientation as the original
• Test movement for smooth travel before fully reassembling

This evaporator assembly circulates refrigerant and absorbs heat inside the freezer compartment to keep the refrigerator cool. Replacing a faulty evaporator restores proper cooling and helps prevent frost buildup and temperature issues. What it does:

• Contains the evaporator coil and housing that remove heat from the freezer air
• Enables the refrigeration cycle so the appliance reaches and holds set temperatures
• Affects frost control—worn or damaged units can lead to excessive ice buildup
• Commonly linked to symptoms like poor cooling, freezer frost, or frequent compressor runtime

• One evaporator assembly (coil and housing)

• Disconnect power to the appliance before beginning any service
• Remove interior panels and shelves to access the evaporator compartment
• Handle the assembly carefully; avoid bending fins or damaging connections

This rail holder secures a door rail to keep the door aligned and stable, restoring smooth opening and closing. It's a direct-fit replacement designed to match the OEM mounting points and restore proper door support. What it does:

• Holds the door rail in place so the door stays aligned and operates smoothly
• Prevents rail movement that can cause rubbing, rattling, or uneven closing
• Restores proper support where a worn or broken holder causes loose or sagging rails
• Helps eliminate noise and misalignment symptoms linked to a failed rail support

• One rail holder

• Disconnect power and follow the appliance manufacturer's service instructions before beginning repair
• Remove surrounding trim or screws as needed to access the rail; keep fasteners for reassembly
• Handle door components carefully to avoid damaging glass or seals; a second pair of hands may help
• Verify part orientation and fit before tightening fasteners;

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

The Glass Shelf is an OEM part for LG refrigerators. It provides a durable surface for organizing and displaying items inside the refrigerator and freezer compartments.

Causes of a faulty shelf can include chips or cracks developing from repeated loading and unloading of items over time. Temperature fluctuations may also cause warping.

Symptoms of a problematic glass shelf include:

• Sagging or bowing that prevents proper fitting
• Breaks or weak spots that compromise strength
• Difficulty removing or replacing the shelf

This OEM LG part is also compatible with some Kenmore models.

This sub PCB assembly is an electronic control board used in select LG appliances. It manages signals and low-voltage power for a specific feature or module, helping restore normal operation when the original board becomes unresponsive or fails.

• Provides low-voltage control for the designated function or user interface
• Communicates with the main control to execute settings and cycles
• Helps resolve symptoms such as unresponsive controls, blank/flickering display, intermittent operation, or related error codes
• Supports reliable operation of the affected subsystem after replacement

• Disconnect power at the breaker; shut off gas/water if applicable
• Use ESD protection and handle the board by the edges
• Photograph wire locations; transfer connectors one at a time to avoid miswiring
• Follow the service sheet for any required option-code entry, reset, or diagnostic check after installation

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This hinge secures and guides a refrigerator door for reliable opening and closing. It restores proper door alignment to help maintain an airtight seal and prevent sagging or rubbing. What it does:

• Supports the refrigerator door and attaches it to the cabinet frame
• Guides smooth door movement and maintains alignment
• Helps prevent door sag, uneven gaps, and items catching when opening/closing
• Reduces rubbing, scraping or abnormal door noise caused by a worn hinge

• Disconnect power and remove food from the door before starting; support the door to prevent dropping
• Use the factory mounting screws and follow OEM torque and alignment steps
• Check door position and seal after installation; adjust hinge mounting if necessary

This rail guide assembly restores smooth, stable sliding for a refrigerator/freezer drawer or shelf drawer, helping the drawer track properly and reducing rubbing or sticking during use. What it does:

• Replaces a worn or damaged drawer slide rail to restore proper alignment and smooth movement
• Helps stop drawers from sticking, binding, scraping, or falling out of track
• Supports the drawer weight and guides it in and out evenly
• Reduces noise caused by misaligned or worn rails

• Disconnect power (and water, if applicable) before servicing the appliance
• Remove the drawer or shelving to access the rail; retain fasteners for reuse unless new ones are provided
• Inspect matching rail on the opposite side; replace both sides if both show wear for best performance

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This damper assembly controls airflow between compartments to help maintain consistent refrigerator temperatures and restore proper air distribution. It replaces a damaged or stuck damper that interferes with cooling balance. What it does:

• Regulates fresh food/freezer airflow by opening and closing the inlet
• Helps correct uneven temperatures or reduced cooling caused by a stuck or broken damper
• Stops unwanted drafts when the damper is closed
• Operates with the fridge's control system to respond to temperature changes

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels or shelving to reach the damper housing
• Handle plastic parts and wiring gently; avoid forcing connectors

Note: Left Rail Cap