Kenmore Refrigerator 795.71069010 (79571069010, 795 71069010) Parts

This damper assembly controls airflow between compartments to help maintain consistent refrigerator temperatures and restore proper air distribution. It replaces a damaged or stuck damper that interferes with cooling balance. What it does:

• Regulates fresh food/freezer airflow by opening and closing the inlet
• Helps correct uneven temperatures or reduced cooling caused by a stuck or broken damper
• Stops unwanted drafts when the damper is closed
• Operates with the fridge's control system to respond to temperature changes

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels or shelving to reach the damper housing
• Handle plastic parts and wiring gently; avoid forcing connectors

This rail guide assembly supports and guides a sliding drawer/rack along its track so it opens and closes smoothly. Replacing a worn or broken guide restores proper alignment and motion, helping prevent sticking, jamming, or uneven travel.

• Supports and stabilizes the drawer/rack on its slide rail
• Helps ensure smooth, straight opening and closing
• Can address issues like binding, noise, or misalignment
• Replaces cracked, warped, or broken guide components

• Disconnect power and, if applicable, shut off water before servicing
• Remove the drawer/rack and retain any reusable hardware
• Install the new guide in the same orientation as the original
• Test movement for smooth travel before fully reassembling

This evaporator assembly circulates refrigerant and absorbs heat inside the freezer compartment to keep the refrigerator cool. Replacing a faulty evaporator restores proper cooling and helps prevent frost buildup and temperature issues. What it does:

• Contains the evaporator coil and housing that remove heat from the freezer air
• Enables the refrigeration cycle so the appliance reaches and holds set temperatures
• Affects frost control—worn or damaged units can lead to excessive ice buildup
• Commonly linked to symptoms like poor cooling, freezer frost, or frequent compressor runtime

• One evaporator assembly (coil and housing)

• Disconnect power to the appliance before beginning any service
• Remove interior panels and shelves to access the evaporator compartment
• Handle the assembly carefully; avoid bending fins or damaging connections

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

The Door Switch is an OEM part for LG refrigerators. It is responsible for detecting whether the refrigerator door is open or closed, allowing the appliance to control the interior light and, in some models, the cooling functions accordingly.

Causes of a bad door switch can include wear and tear from frequent use, electrical issues, or physical damage to the switch mechanism. A faulty door switch can lead to improper operation of the refrigerator's light or cooling system, affecting overall performance.

Symptoms of a bad door switch include:

• Interior light not turning on or off properly
• Refrigerator not cooling properly or running continuously
• Door alarm not functioning correctly
• Intermittent or unresponsive switch operation

This OEM LG part is also compatible with Sears/Kenmore.

Note: 90 degree elbow coupler (Fits 1/4" diameter tubing on each end) For 5/16" elbow connector, order part# 4932JA3009B.

The Water Line Union is an OEM part for LG refrigerators. This component connects sections of the water line, ensuring a secure and leak-free passage of water to the refrigerator's icemaker and water dispenser. It is an elbow tube union connector, which connects two tubes at a 90-degree angle.

Causes of a bad water line union can include wear and tear from frequent use, damage from high water pressure, or deterioration due to mineral buildup and age. A compromised union can lead to water leaks and disruption in the water supply.

Symptoms of a bad Water Line Union include:

• Water leaks around the connection points
• Reduced water flow to the icemaker or water dispenser
• Puddles or moisture near the refrigerator
• Unusual noises from the water line

This OEM LG part is also compatible with Sears/Kenmore.

This door basket restores secure storage on your refrigerator's inner door. It replaces a cracked, loose, or missing bin so bottles and condiments stay organized and easy to access.

• Provides on-door storage for jars, bottles, and condiments
• Snaps into the molded door rails/tabs for a secure fit
• Restores lost capacity and organization when a bin is damaged or missing
• Common symptoms: cracked bin, broken tabs, bin falls off, won't stay level

• Disconnect power and remove items from the door before starting
• Lift the old bin straight up and out of the door slots
• Align the new bin with the slots and press down until fully seated
• The bin is securely engaged before reloading items

This sub PCB assembly is an electronic control board used in select LG appliances. It manages signals and low-voltage power for a specific feature or module, helping restore normal operation when the original board becomes unresponsive or fails.

• Provides low-voltage control for the designated function or user interface
• Communicates with the main control to execute settings and cycles
• Helps resolve symptoms such as unresponsive controls, blank/flickering display, intermittent operation, or related error codes
• Supports reliable operation of the affected subsystem after replacement

• Disconnect power at the breaker; shut off gas/water if applicable
• Use ESD protection and handle the board by the edges
• Photograph wire locations; transfer connectors one at a time to avoid miswiring
• Follow the service sheet for any required option-code entry, reset, or diagnostic check after installation

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly