Kenmore Refrigerator 795.75014400 (79575014400, 795 75014400) Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This is a replacement retaining pin used to secure small moving parts and assemblies in compatible LG appliances. It restores proper alignment and holds components in place so assemblies operate smoothly. What it does:

• Secures and locates components within an assembly to prevent shifting or disengagement
• Helps maintain proper alignment for moving parts that can cause noise or malfunction when loose
• Commonly used where a small, durable metal pin is needed to retain clips, levers, or linkages
• Simple, single-purpose part — replacement when the original is bent, worn, or missing

• One retaining pin

• Unplug the appliance or disconnect power before servicing
• Access the affected assembly per the appliance service instructions; small fasteners or clips may need removal
• Use pliers or appropriate hand tools to remove/install the pin; avoid forcing to prevent damage
• Keep track of orientation and any associated clips or washers during disassembly

A replacement refrigerator door gasket that restores the door seal to help maintain proper cooling and energy efficiency. Replaces torn, cracked, or hardened gaskets to reduce warm air leaks and moisture buildup. What it does:

• Seals the refrigerator door to keep cold air inside and warm air out
• Helps reduce frost buildup and prevents moisture from entering the compartment
• Supports consistent internal temperature for better food preservation
• Stops drafts and improves compressor efficiency when sealing properly

• Disconnect power to the appliance before starting any repair
• Remove the old gasket by loosening door trim or fasteners as needed; clean the sealing surface before installing the new gasket
• Press the new gasket into the channel evenly and ensure the magnetic/locking edge seats fully around the door
• After installation, close the door and check for gaps; allow the gasket to form to the door over normal use

A replacement glass refrigerator shelf that provides a sturdy, easy-to-clean surface for storing food and containers. Restores lost storage space and helps keep items organized and visible. What it does:

• Supports food, containers and small appliances inside the refrigerator
• Creates a flat, stable storage surface for better organization
• Helps contain spills on a single surface for easier cleanup
• Restores damaged, cracked or missing shelving to regain full shelving capacity

• One glass shelf

• Handle glass carefully and wear cut-resistant gloves to prevent injury
• Remove food and other items from adjacent shelves before installing
• Slide into existing shelf tracks or clips until fully seated; do not force
• If shelf hardware is damaged or missing, replace mounting clips or supports before use

The Crisper Drawer Cover Support is an OEM replacement part for LG refrigerators. It provides reinforcement to the drawers that hold fruits and vegetables, keeping them in place securely. The cover support prevents sagging of drawer fronts over time from the weight of stored items.

Symptoms of a faulty crisper drawer cover support include:

• Drawer fronts bowing inward or sagging downwards
• Items inside the drawer shifting during opening and closing  
• Gaps emerging around the drawer perimeter when closed

Causes can be normal plastic fatigue after long-term use. Drawers holding excessively heavy loads increase stress on the supports.

This OEM LG part is compatible with select Kenmore models as well.

This genuine OEM part is a control board assembly for refrigerators. The control board assembly is the main circuit board that controls the refrigerator's primary functions such as adjusting and maintaining temperature. Over time, a refrigerator's control board can become inoperable due to excessive use. If the refrigerator is no longer cooling and failing to maintain its desired temperature, the control board might need to be replaced.To replace the control board assembly, start by unplugging the refrigerator. After that, proceed to open the freezer door and uninstall the side panel to gain access to the old control board. Once accessed, remove the wire harness and any individual wires attached to the control board assembly. Unfasten the mounting screws holding the assembly in place, and pull the control board out. Set it to the side, and proceed to install the new board. Reattach the wires in their correct terminals, and reinstall the side panel. This authentic replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with LG brand refrigerators.

This replacement control panel cover protects the console area and restores the appliance's finished appearance. It shields buttons and electronics from spills, dust, and everyday wear so controls stay secure and accessible. What it does:

• Protects the control console and underlying electronics from dust, moisture, and impact
• Restores a clean, finished appearance when original cover is cracked, warped, or missing
• Helps keep buttons and switches aligned and functioning properly by securing the front housing
• Reduces risk of debris getting into the control area, which can cause intermittent operation

• Always unplug the appliance or disconnect power before starting work
• Basic hand tools typically required (screwdriver, nut driver); remove console or trim per service instructions
• Handle carefully to avoid scratching the new cover; align clips and fasteners before securing

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

This grille cover protects the appliance's cooling/ventilation fan and helps direct airflow where it's needed. It restores the cabinet finish and keeps debris away from the fan housing for more reliable operation. What it does:

• Shields the fan from loose debris and small objects that can cause damage
• Helps channel airflow for proper cooling/ventilation
• Prevents direct contact with fan blades for improved safety
• Reduces rattling or vibration caused by damaged or missing grille

• Disconnect power to the appliance before beginning any work
• Remove any trim or access panels as required to reach the fan area
• Secure with the factory fasteners; do not overtighten to avoid cracking
• Handle edges carefully; wear gloves if needed and test operation after reassembly

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function