Kenmore Refrigerator 795.75292400 (79575292400, 795 75292400) Parts

This sheathed defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice-clogged coils, warm spots, and noisy fan interference.

• Melts frost from the evaporator coil during the defrost cycle to maintain proper airflow
• Symptoms of failure: persistent ice on the back panel, weak cooling, or the evaporator fan striking ice
• A failed heater can cause long run times and temperature swings
• Replace if the element tests open/short or shows visible damage

• Disconnect power before service; allow components to warm to reduce risk of cracking brittle plastics
• Remove shelves and the evaporator cover; carefully defrost ice—do not chip or pry against the fins
• Transfer original clips/insulators if present; route wires as original and make firm electrical connections
• After reassembly, ensure the drain area is clear and the fan spins freely

This genuine OEM part is a control board assembly for refrigerators. The control board assembly is the main circuit board that controls the refrigerator's primary functions such as adjusting and maintaining temperature. Over time, a refrigerator's control board can become inoperable due to excessive use. If the refrigerator is no longer cooling and failing to maintain its desired temperature, the control board might need to be replaced.To replace the control board assembly, start by unplugging the refrigerator. After that, proceed to open the freezer door and uninstall the side panel to gain access to the old control board. Once accessed, remove the wire harness and any individual wires attached to the control board assembly. Unfasten the mounting screws holding the assembly in place, and pull the control board out. Set it to the side, and proceed to install the new board. Reattach the wires in their correct terminals, and reinstall the side panel. This authentic replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with LG brand refrigerators.

This snap-in hole plug button covers unused panel openings to restore a finished look and help keep out dust and moisture. A simple cosmetic trim piece that snaps into place and blends with the control panel. What it does:

• Covers exposed holes in control panels and consoles to improve appearance
• Helps block dust, lint and small debris from entering appliance openings
• Prevents accidental contact with internal components through unused holes
• Useful when replacing damaged buttons or finishing a repair

• One snap-in hole plug button

• Disconnect power to the appliance before working on the control panel
• Press the plug into the hole until it snaps flush; use a flat tool gently if needed
• Inspect fit and panel edge for damage; replace if cracked or loose to ensure a secure fit
• If panel removal is required, follow manufacturer instructions to avoid breaking clips

This shelf assembly is a tempered glass storage shelf that provides a flat, stable surface for arranging food and containers in the refrigerator. It restores usable storage space and helps keep items organized and contained. What it does:

• Replaces a cracked, chipped or missing refrigerator shelf to prevent items from falling or spilling.
• Provides a level surface for storing food, pitchers and containers.
• Fits into existing shelf tracks or support clips to lock into position.
• Helps maintain airflow and visibility inside the fresh-food compartment.

• Unplug the refrigerator or switch off power at the breaker before servicing.
• Remove food and supports, then lift the broken shelf straight out, supporting glass to avoid dropping.
• Slide the new shelf into the existing tracks or align with support clips until it seats securely.
• Handle tempered glass carefully and dispose of broken glass per local regulations; wear gloves and eye protection.

This ice bank assembly is the refrigerated bin that stores and helps feed ice from the ice maker to the dispenser, keeping ice contained and ready for use. It restores proper ice collection and flow inside the freezer. What it does:

• Holds and guides ice from the ice maker to the dispenser or access area
• Prevents ice from clogging or falling out of the ice maker area
• Replaces cracked, warped, or damaged ice storage that causes leaks or poor dispensing
• Helps restore normal ice delivery when the ice maker produces ice but it doesn't collect or feed properly

• One ice bank assembly

• Disconnect power to the refrigerator before beginning service
• Work in a dry, well-lit area; remove contents and shelves as needed for access
• Handle edges and the ice bin carefully to avoid damage; wear gloves for grip and protection
• Follow OEM service instructions for removal and reassembly

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

This grille cover protects the appliance's cooling/ventilation fan and helps direct airflow where it's needed. It restores the cabinet finish and keeps debris away from the fan housing for more reliable operation. What it does:

• Shields the fan from loose debris and small objects that can cause damage
• Helps channel airflow for proper cooling/ventilation
• Prevents direct contact with fan blades for improved safety
• Reduces rattling or vibration caused by damaged or missing grille

• Disconnect power to the appliance before beginning any work
• Remove any trim or access panels as required to reach the fan area
• Secure with the factory fasteners; do not overtighten to avoid cracking
• Handle edges carefully; wear gloves if needed and test operation after reassembly

This shelf net is a mesh-style refrigerator shelf designed to support and contain food items while allowing airflow. It replaces torn, stretched, or missing nets to restore storage organization and help prevent items from shifting. What it does:

• Provides a flexible, ventilated surface for storing packaged foods, produce, or deli items
• Helps keep small or irregularly shaped items from falling through larger shelves
• Restores proper storage function when original netting is damaged, loose, or missing
• Compatible with designated shelf frames and snaps into place where equipped

• Unplug the appliance or turn off power to the unit before servicing for safety.
• Empty and remove food items from the affected shelf area before installation.
• Install by aligning the net with the shelf frame and securing per the owner's manual; do not force or modify parts.
• If installation requires removal of shelves or trim, keep fasteners and small parts organized and follow manufacturer instructions.

This replacement guide provides a secure mounting surface to keep the appliance component aligned and operating smoothly. It restores proper fit and reduces rubbing or binding caused by a worn or broken guide. What it does

• Positions and supports the associated component to prevent misalignment and excessive movement
• Reduces scraping, rubbing, or grinding noises caused by a damaged guide
• Helps drawers, doors, or internal assemblies slide and seat correctly
• Restores smooth operation when original guide is cracked, worn, or missing

• One replacement guide

• Disconnect power (and water, if applicable) before starting any repair
• Minimal hand tools are typically required; follow the appliance service manual for exact steps
• Inspect surrounding clips, screws, and tracks; replace any damaged hardware for best results