Kenmore Refrigerator 795.77199600 (79577199600, 795 77199600) Parts

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This replacement slide rail restores smooth movement and stable support for a dishwasher rack, helping the rack glide in and out without binding. It addresses worn or broken rack guides that can cause noisy or uneven rack movement. What it does

• Guides and supports the dishwasher rack for consistent, level sliding
• Replaces a cracked, bent, or worn rail that causes the rack to stick or derail
• Reduces noise and friction during rack travel for easier loading and unloading
• Helps maintain proper rack alignment so dishes load and wash evenly

• Basic hand tools typically required; disconnect power and water to the appliance before starting
• Remove the affected rack and any clips or stops to access the old rail
• Compare the new rail to the old part for orientation and mounting locations before installing
• If fasteners or clips look damaged, replace them as needed; test rack movement after installation

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This replacement screw secures panels and components on LG appliances to restore proper alignment and prevent rattling or loose parts. It's a direct-fit fastener used where OEM mounting hardware has become stripped, lost, or damaged. What it does:

• Secures panels, brackets, or trim to maintain appliance structure and alignment
• Helps stop vibration noise caused by loose panels or components
• Replaces missing or damaged mounting hardware to prevent parts from shifting
• Restores proper fit where stripped or worn screws no longer hold

• Use the correctly sized screwdriver or bit to avoid stripping the head
• Tighten snugly but do not overtighten; excess torque can strip threads or crack plastic
• If working near electrical components, unplug the appliance first to ensure safety
• Keep removed screws organized during disassembly to match locations on reassembly

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling or loose parts. Simple, direct replacement when a worn or missing screw causes loose panels or intermittent contact. What it does:

• Fastens panels, brackets, or small components to maintain proper alignment and reduce vibration
• Prevents loose trim, covers, or assemblies that can cause noise or improper sealing
• Replaces missing, stripped, or corroded screws that interfere with reliable operation
• Works wherever the OEM screw specification is required for secure mounting

• Use the matching screw hole and tighten until snug; avoid over-torquing to prevent stripping
• Disconnect power to the appliance if accessing electrical or moving parts near the work area
• If multiple screws are missing or panels are damaged, replace all fasteners for even support

A single mounting screw used to secure panels, brackets, or components in place so assemblies stay stable during normal appliance use. Simple replacement for stripped or missing fasteners. What it does:

• Secures panels, trim, brackets or interior components to prevent rattling or movement
• Restores proper fit and alignment after service or accidental damage
• Helps reattach parts removed during maintenance or part replacement
• Small, durable fastener designed for appliance interior mounting applications

• Use the correct screw driver or bit to avoid stripping the head
• Match screw length and thread engagement to the original location before tightening
• Tighten until snug—do not overtighten to avoid cracking plastic or damaging threads
• Disconnect power and follow appliance safety procedures before performing repairs

This is a genuine replacement mounting screw designed to secure appliance panels and internal components, restoring proper fit and stopping movement. Fits specified LG assemblies where the original screw is missing or damaged. What it does:

• Secures panels, brackets, or small components to prevent rattling and misalignment
• Restores proper attachment when original screw is stripped, lost, or broken
• Helps eliminate vibration noise caused by loose fasteners
• Matches OEM fit and thread form for reliable reassembly

• One mounting screw

• Disconnect power and water before beginning any service
• Use the correct driver and do not overtighten to avoid striping threads or cracking components
• Keep removed screws organized to ensure correct replacement locations
• If threads are damaged, replace mating clip or insert as recommended by OEM

This slide rail replaces a damaged or worn drawer support to restore smooth opening and closing of the appliance drawer. It provides a stable guide that helps the drawer track properly and reduces sticking or uneven movement. What it does:

• Guides the drawer along its track for smooth, controlled motion
• Prevents drawer sagging and binding caused by worn or bent rails
• Helps maintain proper alignment so the drawer opens and closes evenly
• Commonly replaced when drawers feel loose, jam, or pull unevenly

• One replacement slide rail

• Turn off power and remove contents from the drawer before starting work
• Remove the drawer per the appliance service instructions to access the rail
• Compare the new rail to the old part to ensure correct orientation and fit
• Use proper hand tools; avoid forcing parts to prevent damage to surrounding components

This screw is a direct-fit replacement fastener that secures panels, brackets, and internal components. Replacing a missing or stripped screw helps stop rattling and keeps parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets, or internal components to restore proper fit
• Replaces missing or damaged hardware that can cause rattling or loose parts
• Restores alignment so doors, shelves, or assemblies operate smoothly
• Provides a straightforward hardware fix without replacing larger assemblies

• Use the matching screwdriver or driver bit to avoid stripping the head
• Do not overtighten — snug until seated to avoid damaging threads or plastic parts
• Disconnect power or follow appliance safety instructions before servicing electrical areas
• Keep removed hardware organized and save any damaged parts for inspection

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

Replacement drawer tray assembly that restores the bottom surface of a refrigerator drawer for organized storage and smooth operation. Use this part when a drawer bottom is cracked, warped, or not seating correctly to keep contents supported. What it does:

• Forms the bottom of a refrigerator drawer to support produce, packaged foods and other items.
• Replaces cracked, warped or otherwise damaged trays that can cause items to tip or spill.
• Helps drawers slide and seat properly by restoring the tray's fit and alignment.
• Restores a hygienic, easy-to-clean surface inside the drawer.

• Unplug the appliance or shut off power at the breaker before working on the refrigerator.
• Remove drawer contents and pull the drawer out; remove any retaining clips or fasteners holding the tray.
• Align the replacement tray with the drawer tracks/tabs and reattach any clips or screws; test drawer operation before returning contents.
• Use gloves to protect hands from sharp edges; for model-specific guidance.

This ice bucket stores ice produced by the refrigerator's ice maker, keeping ice contained and easy to access. It replaces a cracked, missing, or damaged bin to restore proper ice storage and hygiene. What it does:

• Holds and contains ice produced by the appliance's ice maker.
• Replaces cracked, warped, or broken buckets that allow ice to spill or become contaminated.
• Useful when the ice bucket is missing, jammed, or no longer seats correctly in the freezer.
• Helps ensure clean, manageable ice for dispensing or manual access.

• Remove remaining ice and unplug the refrigerator or switch the ice maker off before replacing the bucket.
• Align the bucket with the bin guides or tracks and slide it into place until it seats securely.
• Wash the new bucket in warm, soapy water and rinse before first use; avoid abrasive cleaners or high heat.