Kenmore Refrigerator 795.77542600 (79577542600, 795 77542600) Parts

This screw is a direct-fit replacement fastener that secures panels, brackets, and internal components. Replacing a missing or stripped screw helps stop rattling and keeps parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets, or internal components to restore proper fit
• Replaces missing or damaged hardware that can cause rattling or loose parts
• Restores alignment so doors, shelves, or assemblies operate smoothly
• Provides a straightforward hardware fix without replacing larger assemblies

• Use the matching screwdriver or driver bit to avoid stripping the head
• Do not overtighten — snug until seated to avoid damaging threads or plastic parts
• Disconnect power or follow appliance safety instructions before servicing electrical areas
• Keep removed hardware organized and save any damaged parts for inspection

This replacement screw secures panels and internal components in compatible LG appliances, restoring proper fit and preventing rattles or loose parts. Use it to replace a missing or stripped fastener for a snug, reliable fit. What it does

• Fastens panels, brackets, or components to appliance frame or assemblies
• Helps stop vibration and rattling caused by missing or loose screws
• Restores proper alignment of removable panels or covers
• Works where the original appliance screw has worn, stripped, or gone missing

• Replacement screw as shown

• Disconnect power and water supply to the appliance before beginning any repair
• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Thread carefully and avoid over-tightening to prevent damage to threads or components
• Keep removed screws organized and compare head and length to the replacement before installing

This door stopper cushions and limits an appliance door's travel to prevent slamming and reduce wear on the hinge. It helps the door close smoothly and reduces noise for a better user experience. What it does

• Stops and cushions the door at the end of its swing to prevent hard impacts
• Reduces hinge and cabinet wear caused by repeated slamming
• Helps eliminate banging or rattling noises during door movement
• Can restore proper door feel when the original stopper is cracked, worn, or missing

• One door stopper

• Service with the appliance unplugged and/or power disconnected for safety
• Typically installed at the hinge/cabinet area using basic hand tools; may require removing a trim or access panel
• Inspect hinge screws and mounting area; replace any damaged hardware and tighten to secure the stopper

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

Refrigerator shelf assembly that replaces a damaged or missing internal shelf, restoring flat, secure storage for food and containers. Helps keep items level and organized inside the fridge. What it does

• Replaces a broken, cracked, or missing refrigerator shelf to restore usable storage space.
• Provides a flat, stable surface for jars, bowls, and containers so items won't tip or slide.
• Prevents food from sagging between compartments and improves organization and accessibility.
• Matches factory-fit shelf mounts and seating points for correct alignment when installed.

• Remove all items from the shelf area before installing; handle glass or trim with care and wear protective gloves if needed.
• Slide or seat the shelf into the factory supports or track until it clicks or sits flat; some models require lifting slightly to engage rear tabs.
• No electrical disconnect is typically required, but follow the refrigerator owner's manual and disconnect power if instructed for your model.
• If the shelf has clips or trim pieces, verify they are properly engaged and undamaged before use.

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

Right side upper hinge.

This small sleeve fits over the hinge pin to provide a smooth pivot and maintain proper door alignment. Replacing a worn bushing helps eliminate wobble and squeaks so the door opens and closes correctly.

• Supports the hinge pin/shaft to reduce friction and wear
• Helps keep the door aligned and at the correct height at the hinge
• Can resolve door wobble, sagging, squeaking, binding, or rubbing
• Improves smooth opening/closing and reduces play at the hinge

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door before removing hinge fasteners; note the order of spacers/washers
• Replace the bushing on the hinge pin and reassemble in the same stack-up
• Verify door alignment and operation after installation

This supporter, holder is the small interior bracket that secures its matching holder/assembly inside your refrigerator. Replace a cracked or missing support to restore a solid, level fit and keep the component from wobbling or dropping.

• Provides structural support for the designated holder/assembly inside the fresh food compartment
• Keeps the component aligned so shelves/covers/bins sit level and operate smoothly
• Direct replacement for a broken, warped, or missing support
• Typical symptoms include: holder won't stay attached, tilting or sagging, rattling when doors close, visible cracks or stripped tabs

• Disconnect power to the refrigerator before servicing
• Remove the item the support holds (such as the related shelf, cover, or bin)
• Release locking tabs and/or remove screws; transfer any reusable hardware
• Align and snap or screw the new support into place, then reinstall the component and verify a secure fit

This bracket holder assembly is a structural mount used to secure an internal component, keeping it properly positioned during operation. Replacing a cracked or loose bracket restores support and helps prevent vibration, rattling, and misalignment.

• Provides a fixed mounting point to hold the supported part in place
• Maintains alignment to reduce vibration, rubbing, or noise
• Helps prevent shifting that can lead to premature wear
• Common symptoms: broken tabs or cracks, loose/misaligned component, rattling noises, visible damage to the old bracket

• Disconnect power; shut off water or gas if applicable
• Note screw locations and orientation; take a photo before removal
• Transfer any reusable clips or hardware from the old bracket
• Tighten fasteners evenly and avoid over-tightening to prevent damage

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This lamp reflector mounts behind the refrigerator light to direct and spread illumination throughout the compartment. Replacing a cracked, melted, or missing reflector helps restore bright, even lighting so you can clearly see food and shelves. What it does

• Sits behind the interior lamp to reflect light forward into the compartment
• Helps maintain even, consistent illumination and reduces shadows
• Typical symptoms: dim or uneven lighting with a good bulb, yellowed/melted reflector, cracked or missing reflector
• Supports proper visibility around shelves and bins

• 1 lamp reflector

• Disconnect power before servicing to avoid electric shock
• Remove the light lens/cover and bulb to access the reflector
• Reuse existing screws or clips as applicable
• Do not overtighten fasteners; reinstall bulb and lens, restore power, and test

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.

This PTC cover protects the refrigerator's PTC/compressor start device from dirt, moisture and accidental contact, helping the start device operate reliably. It's a simple replacement that restores the protective enclosure for the start assembly. What it does:

• Shields the PTC/compressor start relay and wiring from debris and moisture that can cause malfunctions
• Helps prevent accidental shorting or contact with terminals during operation or service
• Can resolve symptoms where the start device is exposed or the compressor area shows visible wear or damage
• Maintains correct positioning and protection of the start components for consistent compressor starting

• One PTC cover (protective enclosure) as shown

• Disconnect power to the appliance before starting any repair
• Replace only when the start device or cover is exposed and you can access compressor/start assembly safely
• Avoid bending or stressing terminals and wiring when removing or installing the cover